Top 20
Gestetner DSc224 Copier Questions & Answers
Show drum unit
Impossible to clean anything in a picture. You need to have the actual unit :)
DSC224 printer displays low on fuser oil
There is a sensor that need to be cleaned if the code will not clear. I believe there is a black float that is part of the fuser bottle. If you swing out the oil bottle and look where the float would be... There is a sensor, clean the sensor and make sure it is plugged in correctly... Good Luck
We want install cd
here;s the download link
http://www.ricoh-support.com/enduser/gestetner/advsearchresult.asp?type=download&ProdName=Multi+Functional+Products
Wat does it mean if
the main reason for this could be when you replaced the toner cartridge you have either not put in correctly or an incorrect toner put in. Check the other cartridges to see if when you remove one you get the same error if this is the case you could have a faulty toner. Is the toner an origina Gestetner toner you may need to return it...K
I have a problem with
Hello,
See? Ya need to listen to the baby. It told you it was low for days. Ok, I have to assume you have filled the oil bottle.But now the copier can't know that. We need to reset the error code.You will need to go into the SERVICE MODE in order to do this. In order to go into sevice mode you must press a few buttons. Locate the yellow CLEAR button located above the 9 key pad. Now locate the red STOP button at the bottom. Ok, press the Clear button for a moment and then press the numbers 1-0-7, then press the STOP button. So....CLEAR(release) 1(release) 0 (release) 7(release) then press and hold the RED STOP button for 5 seconds. The screen will change indicating you are in service mode. On the menu you will see tabs. Select COPIER. Now you will see a new screen that will have several tabs across the top.SP DIRECT should already be highlighted, if not touch it and highlite it. Now, use the keypad and press "5810" and then press the # sign. When you press the # sign the display should ask you if you want to EXECUTE. Press EXECUTE. Now unplug the copier. Wait a second or two and plug it back in. This should do it.Glad to help and please let fixya know I helped you. SPINAL
Dsc224 ploblem sc142
Error Detection White Balance
The White Balance can not be resolved • glass or optical section
within the target at the Spotted
automatic gain control. • Card SBU defective
• Map BICU defective
• Exposure lamp defective
• Cruise the lamp defective
Waste Bottle 2 full
There are two tanks on toner cete machine. One down, one in the middle. This is the one that must be emptied
Using avery 5160 labels in the machine, ususally
Try to choose thick paper in the printing properties.
But first ok all make sure you are using labels for laser machine. It should be or else you can damege the equipment. That info came in the box
C0221
needs cartridge replacement or reset setting.
I have an sc 672
Try, after powering down, removing and reseating the controller board (the one that the print cable plugs into) -Carl
Hi, we have Gestetner DSc224 printer. I have to
Hi,
It sounds like the only thing left to do is to create a new shared folder on your main pc, and pointing this folder as the default for when documents are scanned. Follow the link for a step by step walk through.
http://www.techstarcorp.net/scanrouter_setup.htm
Al
Jsc570 code
This is a common error for the dev fam motor if you hav etaken th back off and done any repairs the connector is loose or the fan may be clogged up with toner and cant turn.. try cleaning with brush or vac..hope this helped A
Service code sc544
It is a fuser overheat error....really has to be checked by a technician...
note that any Ricoh tech can also do it as it is a Ricoh machine
Not finding what you are looking for?