20 Most Recent Dewalt DC925 Cordless Drill - Page 2 Questions & Answers

under my handle for this site, go to the tip section and I have detailed instructions on how to remove this chuck. Let me know if you need more assistance.

there should be different settings for the clutch. there is a wheel behind the chuck which you can turn for the settings. If it is set at the high setting the clutch is worn and has to be replaced.

Hi!!

The hammerdrill function is set by the selector switch, the switch itself may look fine from the outside, but, if it is not switching functions, you should open the hammerdrill and check the switching mechanism, even if you don't have an idea of how it works, after a visual inspection to the switching mechanism, common sense will tell you what's wrong, it is actually pretty simple.

Good Luck!! A HELPFUL - 4 THUMBS - rating for this solution would be greatly appreciated. Thank you for using FixYa.

THE BRUSHES COME IN A SET AND ARE AVAILABLE FROM MOST SERVICE CENTERS. IF YOU GO ONLINE YOU CAN DOWNLOAD A SCHEMATIC FROM DEWALT SERVICE NET. ENTER IN THE MODEL NUMBER AND CHOOSE THE TYPE # AND YOU CAN GET THE PART # FOR THE CLUTCH ASSY, THE TOOL COMES APART PRETTY EASY, THE FRONT OF THE TOOL IS HELD IN PLACE BY 4 SCREWS 15 TORX I BELEIVE AND THE CLUTCH AND TRANNY ASSY IS ITS OWN MODULE, BUT CALL YOUR LOCAL SERVICE CENTER AND THEY SHOULD BE ABLE TO WALK YOU THROUGH IT. SINCERELY JIMS TOOL SERVICE

åpne chucken helt og skru ut senter låseskruen i bunnen av ckucke'en. >Denne er venstregjenget/motsatte gjenger. >Sett fast en stor unbrako i kjeften på chucken og slå skaftet hurtig med en hammer for å skru av selve chucken. Denne skrues av med normale gjenger.

You must never oil the chuck so if this has been done then it can be the cause of your problem

Hi,
Try and work some WD-40 into the chuck to get it to free up...

heatman101

you can go to Dewaltservicenet.com and in the middle of the page towards the bottom you will find a box for manual. Type in your model number and you can download a schematic for the tool.

it is unlikely that you had two defective batteries, it makes more sense that the charger is overcharging them. It would have to be checked with an amp meter to be sure

They all do that a bit. The sparks when starting up and stopping are normal. If it has been used alot brushes may be a good idea but before they need to be changed it will spark quite a bit.

It will not hurt to inspect the amount of brush material remaining.

On my DW988 the ring would go past 21 a couple of clicks to a symbol that looks like a yellow T and that would be hammer mode when I press down to drill.

go to the tup section and there are detailed instructions on how to remove. You might also try and going to my profile and in the left hand side is my tip on how to do this also. Let me know if you cant find it and I will reenter again.

turn the torque adjustment collar until the hammer is selected (there is a picture of a hammer instead of a number there)

You are set on LOCK? or are you set to let go at some lesser level? My DeWalt is much older than yours and in the same service with no problem.?

CONTACT YOUR NEAREST TOOLKING STORE THEY WILL ADVISE YOU

Sounds like the battery is not making a good connection inside the drill handle. Clean the contacts inside the handle where the battery plugs. Clean the contacts on the battery. If there are any springy tabs in either of these places, pry them up slightly to increase the pressure between the contacts.

Clean with wire brush, sandpaper, electrical contact cleaner.

If this doesn't work, get back to me and we'll go to the next step.

Charlie

Possible reasons for this behavior: Blinks Long (Red Light): If your battery is too hot, the charger will blink the red light rapidly and for an extended duration. To prevent this, ensure that your battery is not exposed to direct sunlight or excessive heat. Give it some rest to cool down. Blinks Short: If the battery is too cold, it will blink short and fast. This could be due to prolonged exposure to cold temperatures or the battery being idle for an extended period. Allow the battery to charge for a while or bring it to room temperature to resolve this issue. Blinks Very Fast (Doesn't Go Away): If the light is blinking very fast and persists, it indicates that your battery has gone bad and needs replacement.

A photo would greatly help with your issue, are both wires still attached to the capacitor?? in not, the capacitor must be replaced with one of the same value, if the capacitor is ok, look for a wire with solder on the end but nothing else attached to it, or a solder point on a card with a hole in it or a solder joint that has broken free from the card,,, if you can solder well, and have the equipment,. it is good at this point because You'll need to re-solder them back together,, again a photo will help me greatly in telling you exactly how to fix

Read the reviews. We see them on Fixya very occasionally and from memory, it was internal fuses blowing. https://www.google.com/search?q=Dewalt+DCR025 ..