Electronic Chart I need an electronic chart or service manual to repair my panasonic stereo model sc ak 600, i live in Colombia - Sout Am?rica and i cannot localize it here my e-mail is [email protected] Thanks ALEJANDRO L?PEZ

ENCs, or Electronic Navigational Charts, are digital versions of paper nautical charts that are used for navigation. In ENCs, different symbols are used to represent features such as buoys, obstructions, and shorelines.

The switch between paper chart symbols and simplified symbols in ENCs can typically be found in the settings or display options of the software or app that is being used to view the charts.
For example, in ECDIS (Electronic Chart Display and Information System), the settings for symbol display can be found in the "Chart Display" or "Chart Display Options" menu, and there may be a setting to switch between "Standard" or "Simplified" symbols.
Similarly in other ENC software like ENC viewer, it can be found in the settings or display options and have the option to turn on/off the Simplified or Detailed Symbol display.

It's important to note that the availability of this option may depend on the specific software or app that you are using, and you may also want to check the user manual or documentation of the software for specific instructions on how to switch between different symbol sets.

What Is A User Chart Point And How Is It Used - Furuno FCR ...

www.manualslib.com > ... > Operator's manual

Furuno FCR-2107 Manual Online: What Is A User Chart Point And How Is It Used. A point is a center point for a sub chart inside a user chart. Sub charts are ...

Furuno Ecdis Fmd 3300 cbt : ??? ???

m.blog.naver.com > sksalwkdus

Jul. 21, 2016 - I can send my Route Plan and User Chart to a FURUNO GPS for display on the ... A point is used to create a Manual Update from a chart object.

ECDIS display

furuno.de > Downloads > Handb?cher1

PDF Open Point page of User Chart. Use Cursor and SELECT button to define location of Points. When you remove selection Enable changes or close User Chart ...

Electronic Chart Display and Information System (ECDIS)

www.furuno.de > Downloads > Handb?cher1
PDF
What is a User Chart Point and for which purpose it is used ? ... points or heads at any instant, has been changed to Heading (Hdg):. · Alarm "2002 No course ...

https://www.manualslib.com/manual/893822/Panasonic-Tc-P42gt30a.html


https://www.manualslib.com/manual/893822/Panasonic-Tc-P42gt30a.html?page=18#manual



Panasonic TC P42GT30A Service Manual Power Led Blinking Timing Chart


Part replacement may be necessary. May required a trained technician to perform replacement.

Download its service manual. It will have all details about error codes.

Dear Friend,
Go to the following link below. Good luck!!!http://www2.panasonic.com/consumer-electronics/support/Audio/Home-Theater/Mini-Systems/model.SC-AK15

Hi pjwivell ..
Are you sure that it SA AK 750?
well here is a here for SC AK750
download the manual and try if it works for you..
http://www2.panasonic.com/consumer-electronics/support/Audio/Home-Theater/Mini-Systems/model.SC-AK750
please give me update if you had any success... thanks

Hello,Please use the chart to determine which stove you have. You will have to look at the model number. The first 3 numbers will be the series on the chart. In most cases an F1 error would require replacement of the electronic control. This part is commonly refered to as an EOC or ERC. However this type of repair is usually reserved for repair specialists.

KENMORE Range/Stove/Oven Fault Codes – 362 Series (General Electric)
F1 = Stuck Touch Pad Key - Replace Electronic Range Control (ERC).

KENMORE - 911 Series (General Electric/Roper)
F0-F1-FF = Failed transistor in Electronic Range Control (ERC).

KENMORE Range/Stove/Oven Fault Codes- 665 Series (Whirlpool)
F1-E0 EPROM Error - Electronic Range Control (ERC).
F1-E1 EPROM Error - Electronic Range Control (ERC).
F1-E2 U/L ERC Errors - Electronic Range Control (ERC).
F1-E3 Fuel Type Fail

Kill power 30 seconds-Cancel-Start/Enter-5 seconds-Should see “E” for electric-
“9” for gas-If code changes again-replace Electronic Range Control (ERC).

KENMORE - 790 Series Electronic Oven Control (Frigidaire)
F1 = Shorted Touch Pad = Electronic Range Control (EOC) Internal check sum error.
Runaway Temp = Replace Electronic Oven Control (EOC).

Kill power 30 seconds - if error returns - replace Electronic Oven Control (EOC).

Thanks

Hello, please use the chart to determine which stove you have. You will have to look at the model number. The first 3 numbers will be the series on the chart. In most cases an F1 error would require replacement of the electronic control. This part is commonly refered to as an EOC or ERC. However this type of repair is usually reserved for repair specialists.

KENMORE Range/Stove/Oven Fault Codes – 362 Series (General Electric)
F1 = Stuck Touch Pad Key - Replace Electronic Range Control (ERC).

KENMORE - 911 Series (General Electric/Roper)
F0-F1-FF = Failed transistor in Electronic Range Control (ERC).

KENMORE Range/Stove/Oven Fault Codes- 665 Series (Whirlpool)
F1-E0 EPROM Error - Electronic Range Control (ERC).
F1-E1 EPROM Error - Electronic Range Control (ERC).
F1-E2 U/L ERC Errors - Electronic Range Control (ERC).
F1-E3 Fuel Type Fail

Kill power 30 seconds-Cancel-Start/Enter-5 seconds-Should see “E” for electric-
“9” for gas-If code changes again-replace Electronic Range Control (ERC).

KENMORE - 790 Series Electronic Oven Control (Frigidaire)
F1 = Shorted Touch Pad = Electronic Range Control (EOC) Internal check sum error.
Runaway Temp = Replace Electronic Oven Control (EOC).

Kill power 30 seconds - if error returns - replace Electronic Oven Control (EOC).

Thanks

Please use the chart to determine which stove you have. You will have to look at the model number. The first 3 numbers will be the series on the chart. In most cases an F1 error would require replacment of the electronic control. This part is commonly refered to as an EOC or ERC. However this type of repair is usually reserved for repair specialists.

KENMORE Range/Stove/Oven Fault Codes – 362 Series (General Electric)
F1 = Stuck Touch Pad Key - Replace Electronic Range Control (ERC).

KENMORE - 911 Series (General Electric/Roper)
F0-F1-FF = Failed transistor in Electronic Range Control (ERC).

KENMORE Range/Stove/Oven Fault Codes- 665 Series (Whirlpool)
F1-E0 EPROM Error - Electronic Range Control (ERC).
F1-E1 EPROM Error - Electronic Range Control (ERC).
F1-E2 U/L ERC Errors - Electronic Range Control (ERC).
F1-E3 Fuel Type Fail

Kill power 30 seconds-Cancel-Start/Enter-5 seconds-Should see “E” for electric-
“9” for gas-If code changes again-replace Electronic Range Control (ERC).

KENMORE - 790 Series Electronic Oven Control (Frigidaire)
F1 = Shorted Touch Pad = Electronic Range Control (EOC) Internal checksum error.
Runaway Temp = Replace Electronic Oven Control (EOC).

Kill power 30 seconds - if error returns - replace Electronic Oven Control (EOC).

Please use the chart to determine which stove you have. You will have to look at the model number. The first 3 numbers will be the series on the chart. In most cases an F1 error would require replacment of the electronic control. This part is commonly refered to as an EOC or ERC. However this type of repair is usually reserved for repair specialists.

KENMORE Range/Stove/Oven Fault Codes – 362 Series (General Electric)
F1 = Stuck Touch Pad Key - Replace Electronic Range Control (ERC).

KENMORE - 911 Series (General Electric/Roper)
F0-F1-FF = Failed transistor in Electronic Range Control (ERC).

KENMORE Range/Stove/Oven Fault Codes- 665 Series (Whirlpool)
F1-E0 EPROM Error - Electronic Range Control (ERC).
F1-E1 EPROM Error - Electronic Range Control (ERC).
F1-E2 U/L ERC Errors - Electronic Range Control (ERC).
F1-E3 Fuel Type Fail

Kill power 30 seconds-Cancel-Start/Enter-5 seconds-Should see “E” for electric-
“9” for gas-If code changes again-replace Electronic Range Control (ERC).

KENMORE - 790 Series Electronic Oven Control (Frigidaire)
F1 = Shorted Touch Pad = Electronic Range Control (EOC) Internal checksum error.
Runaway Temp = Replace Electronic Oven Control (EOC).

Kill power 30 seconds - if error returns - replace Electronic Oven Control (EOC).