WHAT ARE THE COLOR WIRE SEQUENCE TO THE TERMINAL BLOCK ON MAGTAG DRYER. NOT THE CORD SIDE BUT FROM THE DRYER. IE BLUE WIRE GOES WERE/

if you buy a color coded cord and plug then red and black go on thee 2 outer terminals of the power terminal and the white wire goes between these as this is the neutral connection and if it has a green ground wire connect this anywhere to the metal case of the unit, if its a gray cord with no colors then the 2 outer wire on the cord go to the outer terminals on the units power terminal block and the center wire on this cord goes to the center terminal on the unit

Hi josiahschnei...
Follow the link and it will have pictures showing you which wire goes to which terminal
Free Answer...Please take time to rate me.


http://www.selfhelpandmore.com/switch-outlet/dryer-circuit-wiring-and-hookup.php

On the back of the dryer, remove the screw(s) that hold the access cover to the back panel that cover the terminal block where the cord goes through the back panel and connects to the wiring terminal power block, loosen the two screws on the cord clamp the clamp it to the back of the dryer just enough to release the cord, remove the four nuts / screws that are connecting the 4 wires from the cord to the terminal block and or the back of the dryer,with the new 3 wire cord just match the colors on the terminal block with the same color wires that are connected to the other side of the terminal block, red,black on the outer most terminals and the white or green to the middle terminal, IT IS IMPORTANT THAT YOU PLACE A JUMPER WIRE/STRAP FROM THE MIDDLE TERMINAL WHERE THE WHITE OR GREEN WIRE CONNECTS TO THE TERMINAL BLOCK OVER TO THE CASE/CABINET OF THE DRYER, THIS CAN CONNECT TO THE CASE AT ANY AVAILABLE SCREW NEAR THE TERMINAL BLOCK! In short this means that the neutral and ground of the dryer must be connected together in a 3 wire set-up.
GOOD LUCK!

what ever your wall outlet is,(3 hole or 4 hole)just remember on a 4 hole cord the white wire goes to the middle of the terminal block and the black and red wires one on each side of terminal block,color does not matter on those two,ground the green wire to the cabinet,if it is a 3 prong middle wire goes to the middle of the terminal block and the other 2 wires one on each side-mike

The three wire goes on the electrical block on the back of your dryer just like the cord is made. If you look at the cord, it's made flat (Most 3 wire cord are made flat, Some are not) The wire in the middle goes in the middle of the block. The two wires to the outside go to the outside of the block. It makes do difference which wire goes on which side as long as the outside wires go to the outside.
Please rate solution

Always disconnect electricity before beginning this process.

If you are using a 3 wire cord the wires go exactly as you see them. The middle wire goes onto the middle terminal and the outside wires go to the outside terminals which one goes on which side doesn't matter.

All the 4 wire cords I have seen are color-coded. The white wire goes to the middle, the green wire goes to any screw you can reach that goes into the metal case of the dyer. The red and black go to the outside of the terminal block and I usually follow the color code of the interior dryer wiring that already exists. Good Luck.

just remember on a 3 wire cord(if it is gray) the middle wire always goes on the middle of the terminal,the 2 outside wires get mounted one on each side on the terminal broke,if it is a 4 wire cord the white goes on the middle of terminal block,the red and black get mounted one each each side of the terminal block(it does not matter which side you put the red or black wire they are both 120 volt) the green wire gets mounted to the cabinet where ever you can mount it(to metal) your done-mike

Not really sure what you are asking. But if you trying to hook the cord up... Green and white go to the middle terminal Then black or red to either side it doesnt matter which.

doesn't matter both are 110v lines but if you want look up to top screw connections the wires coming to those screws are also colored as long as the red and black are to outside screws dryer will work ok

If your dryer cord is flat and gray, then simply attach the two outside wires from the cord to the left and right screws on the terminal block. Connect the center wire of the cord to the center screw of the terminal block. The only important wire is the center wire of the cord goes to the center screw of the terminal. The two outside wires don't matter.