My machine is a maytag neptune fav6800aww. it is flashing the code uc please help

This is a Clutch issue could be a easy fix if the Tub Seal is not the root cause.

If you get no help at this forum Google This ""Neptune TL Washer FAV6800AWW""

5th post down you will find the SM and support for the "DC and UC" unbalance error codes. Good luck..............DH1200s

Google this; Neptune TL Washer FAV6800AWW

This is a DIY Appliance repair forum and you can get the Service Manual and repair support at that site..

In the Sticky: Neptune TL Washer FAV6800AWW 5 post down you will find a link to the Service Manual. You absolutely need the Service Manual to DIY issues with the machine. It's not the best SM but will get you started. I also have repair post in that sticky to help with the most common issues that I have helped owners with. I'm an owner of a FAV6800AWW top load machine.

In that Sticky I discuss what is the cause of DC or UC unbalance errors and the fix.

Somewhere on this forum I have a response to DC or UC unbalance errors and the fix. It's hard to find my past post on this forum.

Google this; Neptune TL Washer FAV6800AWW

This is a DIY Appliance repair forum and you can get the Service Manual and repair support posted in the sticky at that site.

In the Sticky: Neptune TL Washer FAV6800AWW 5 post down you will find a link to the Service Manual. You absolutely need the Service Manual to DIY issues with the machine. It's not the best SM but will get you started. I also have repair post in that sticky to help with the most common issues that I have helped owners with. I'm an owner of a FAV6800AWW top load machine.

Google this Neptune TL Washer FAV6800AWW

5th post down in the sticky you will find my service notes to get you back in service.

Dave,

Sorry you replaced the TDS.

Google Neptune TL Washer FAV6800AWW that's the Sticky for your machine type. The 5th post down you will find notes to repair.

Post a new thread in that DIY forum not the Stick if you need additional help.

More than likley a Clutch issue. I don't post here very often and is difficult to fin my post. This is not a true DIY forum. I found my old link the other day Clutch Fix

You can't get the Service Manual from this site anymore. Servicematers.com has locked down the site.

Google "Sticky: Neptune TL Washer FAV6800AWW"

Go to the 5 post in this sticky and you will find a link to the FAV6800A/FAV9800A SM and my write up on dc/UC unbalance error codes.

If you need additional help don't post in the Sticky just start a new post and I will help you.

See if this will get you started http://www.fixya.com/support/t2070219-model_fav6800aww_will_not_pump_water_out

I no longer post on this site no way to post a Sticky.

If you want to DIY the repair Google this phrase ""Sticky: Neptune TL Washer FAV6800AWW""" Read the post Part 1; DC or UC unbalance error codes in Spin Cycle what is causing this issue? Part 2 for the fix action.

Post your issue in the repair forum not in the Sticky. Please include your Model Number i.e. FAV6800A or FAV9800A and I will help you.

Are yiy failing in Spin Cycle wuth dC or uC error codes?

If so see if this post Clutch Fix. There is a link to the SM.....D*ick

See if this post http://www.fixya.com/support/t4757262-i_have_a_letter_showing_and_it_say_o_d_w will get you started.


You have lost signaling from the Left Hand Lid Lock. If you want to DIY I will try to help........Rich

Continuous Unbalanced Circuit. Improper signal from Tub Displacement Sensor.
Wet Clothes • Very small clothes loads can cause unbalanced loads - add additional towels. • Excessive suds may have been present. • Check Tub Displacement Sensor connection and main harness connector at machine control board. • Check Tub Displacement Sensor for 0 to 3.0 Volts DC output voltage between ground and the board input. Check for 12 Volts DC input voltage between the ground and the board output. Only check for voltage at the Tub Displacement Sensor. Do not perform a continuity check. See Tub Displacement Diagnostics • Excessive motion was detected in spin Run Quick Spin Test with an empty tub to check Tub Displacement Sensor and machine control board. • Check for restricted drain system.