Hoover Nextra 160 HNWF 3137 Front Load Washer / Dryer Logo

Related Topics:

Anonymous
Anonymous Posted on Nov 07, 2017
Be the first to answer

Hoover washer HNWF 3137-80. Power available, start machine timing light for cycle lights, door light flashes and door locks but door lock light continues to flash. Assume this indicates that controller not getting locked signal and theefore water solenoid does not open and hence machine does not start. Where do I look first please

Answer This Question

4 Related Answers

A

Anonymous

  • Posted on Feb 05, 2008

SOURCE: Hoover Nextra HNWF 3137

this is a condenser washer dryer so water should evaporate to condenser then empty!

Ad

Anonymous

  • 1 Answer
  • Posted on Jun 02, 2008

SOURCE: Hoover Nextra HNWF 3137 washer/dryer

I have the same problem exactly please send me the solution with confirmation of the exact part requested my machine is HOOVER HNL3137 1300rpm/7kg thanks

Anonymous

  • 8619 Answers
  • Posted on Feb 18, 2010

SOURCE: Hoover Nextra HNF2127 washing machine. Lights flashing at finish

Hi


Thanks for using FixYa. The start and pre-wash usually flash due to a clogged drain hose or the water pump. You’ll need to drain the water out of the base and also check to see if there's something stuck inside the pump or the drain hose connected to the pump (pump is usually located at the bottom and towards the back of the washing machine). If the drain line isn't clogged, you may have a problem with the water pump such as a frozen pulley or a broken impeller. If that's the case replace the water pump. Please do accept the solution if the issue is resolved or else revert for further assistance.


Thanks
Rylee

ercupa190

ernesto cuadra

  • 12223 Answers
  • Posted on Jun 29, 2012

SOURCE: Hoover Nextra HNWF 3135 door will not lock

1) test the switch door, you do not have error code.
see the video, and replace for defective switch, or loose wires or broken, or burn.

God bless you

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
2answers

My hoover dynamic washer is not showing an error code but all the lights are flashing and beeping all the time.
If your Hoover Dynamic washer is not displaying any specific error code but all the lights are flashing and it's beeping continuously, there might be an issue with the control panel or a more general system malfunction. Here are some steps you can take to troubleshoot the problem:
  1. Power Cycle the Washer: Turn off the washer and unplug it from the power outlet. Wait for a few minutes, then plug it back in and turn it on again. Sometimes, this simple reset can resolve minor electronic glitches.
  2. Check for Overloaded Washer: If the washer is overloaded with clothes, it can cause the control panel to act abnormally. Try running a smaller load and see if the flashing lights and beeping stop.
  3. Inspect the Water Supply: Ensure that the water supply to the washer is adequate and not restricted. Low water pressure or a clogged water inlet can cause unusual behavior in the washer.
  4. Check the Drainage: Make sure the drainage hose is not clogged or kinked. A blocked drainage system can lead to improper functioning of the washer.
  5. Examine the Door Lock: If the door lock is not engaging properly, the washer might not start or show unusual behavior. Check if the door is securely closed and the lock mechanism is functioning correctly.
  6. Check for Leaks: Look for any leaks around the washer. Water leakage can trigger safety features, leading to flashing lights and beeping.
  7. Inspect the Control Panel: Examine the control panel for any physical damage, moisture, or dirt accumulation. Clean the panel gently and make sure all buttons and knobs are functioning correctly.
  8. Software Glitch: If none of the above steps resolve the issue, it's possible that the washer's control board has encountered a software glitch. In this case, you may need to contact Hoover customer support or a professional appliance repair technician to diagnose and fix the problem.
Read full answer
Jul 23, 2023 • Hoover Washing Machines
0helpful
1answer

Indesit IWD7145K Washing Machine Error code F06 flashing on digital display + all program indicator lights. What does this mean. There is no such error code in the troubleshooting section of the manua
F06 - Door lock fault
Issue: Washing machine door cannot be opened or closed/when the door is closed the machine the programme will not start.
Advice: If your washing machine door will not close, please check for any obstructions in the door lock.
OR,
Switch off the device. Disconnect power. Wait about 3 minutes.
Open the door, then close. Reconnect device to the network.
Start device.

Cause: Door lock fails to close / open door lock triac open / closed,
frequency signal fault

Dado
Read full answer
Feb 12, 2015 • Indesit Washing Machines
0helpful
1answer

Hoover nextra washing machine door wont lock / cycle start
sounds like the door lock mechanism. if this cannot signal it has engaged, to the board, no other function will work (you don't want the washer going with the door open, trust me :) )
Read full answer
Nov 08, 2013 • Hoover Nextra 160 HNWF 3137 Front Load...
0helpful
1answer

Hoover Nextra HNWF 3135 Door Not Locking
1) since you do not have any error code, because you do not mentione, we must shure you have problem with the switch door, test for open or defective and replace, Test the wires loose, or broken wires.

God bless you
Read full answer
Jun 28, 2012 • Washing Machines
0helpful
1answer

Hoover Nextra HNWF 3135 door will not lock
1) test the switch door, you do not have error code.
see the video, and replace for defective switch, or loose wires or broken, or burn.

God bless you
Read full answer
Jun 28, 2012 • Hoover Nextra HNWF 3135 Front Load...
1helpful
1answer

It's STUCK
Hi


The light is flashing due to the door lock error. The door lock is activated as the machine experienced an error or was stopped in middle of a cycle. Or the door was being pulled while the machine was running a cycle. Try unplugging your washer and restart the washer to check if you are still getting the same blinking light. If error is still not resolved then start the rinse/spin cycle & stop the cycle, now press and hold the cancel button for 5-10 seconds. However, if you are still not able to get the door open then you'll need to open the door manually by disassembling the washer. Please post back for any further assistance.

Daniel
Read full answer
Jul 25, 2010 • Whirlpool Duet GHW9150P Front Load Washer
3helpful
5answers

My Hoover Optima OPH 714 D washing machine won't start
Hope your tried switching off the machine for half to one hour, to re plug. Machine might re-set.
If helped, pl click, it could help others.
Read full answer
Dec 07, 2009 • Bosch Washing Machines
16helpful
3answers

Hoover HNL7166 'Start Delay' light flashing
Hoover (Nextra series) washing machines

The 'Start' & 'Pause' LED's will flash together to indicate the error code. You have to count the flashes within each 15 second period to get that error code. The start and the pause LED's will flash together at 1Hz (i.e 1 flash per second) within that 15 second time frame, then will continue and show again within another 15secs and so on.

1 Flash = Interlock fault
2 Flashes = Fill time-out
3 flashes = Drain time-out
4 flashes = Overfill fault presure pipe blocked
5 flashes = NTC error
6 flashes = faulty control board
7 flashes = Motor jammed
8 flashes = Tacho fault
9 flashes = Motor triac on module board
10 flashes = Prog Selector or wiring fault
Read full answer
Jul 27, 2009 • Washing Machines
0helpful
1answer

Door locked light flashing when door is closed
push on the door where the lock is... it may not be fully locked.

Read full answer
Feb 22, 2009 • Hotpoint Aquarius WMA42 Front Load Washer
0helpful
2answers

Hoover Nextra HNWF 3137 washer/dryer
The timer is bad, replace the timer.
Read full answer
Apr 21, 2008 • Hoover Nextra 160 HNWF 3137 Front Load...
Not finding what you are looking for?

View Most Popular

Nextra 160 HNWF 3137 Front Load Washer / Dryer

  • Washing Machines

Related Question

My hoover dynamic washer is not showing an error code but all the lights are flashing and beeping all the time.

  • Hoover Washing Machines

105 views

Ask a Question

Usually answered in minutes!

Popular Questions

I just opened my washing machine door after finishing a wash and there was smoke coming out of the door and a smell of burning. It is a Hoover model no HWB814D-80S.

Hoover Washing Machines

How do I reset a e20 error code on my hoover washing machine

Hoover Washing Machines

Hoover WMH168D error code E08

Hoover Washing Machines

Error code E11 on hoover

Hoover Washing Machines

Hoover washer dryer error code h01

Hoover Washing Machines

Top Hoover Washing Machines Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Brad Brown

Level 3 Expert

19187 Answers

NOEL
NOEL

Level 3 Expert

8606 Answers

Are you a Hoover Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...