Maytag epic I have a maytag epic washer...I keep getting an FH error code about 3 min. into the wash cycle what does this mean and can I fix it?

How to Troubleshoot a Maytag Epic Washer Front Loader Tip Call Maytag for service if any of these procedures doesn't clear the code on the washer display.

Warning Maytag makes several models in the Epic series and operating instructions vary. For model-specific troubleshooting instructions defer to the user manual that came with your machine or contact Maytag support.

Each model in the Maytag's Epic automatic clothes washer series has a computerized processing unit that displays error codes on a digital screen when something goes wrong with the washer. These codes help Maytag service technicians diagnose the unit. If you know the codes, you can troubleshoot the problem yourself, rather than request a service call, possibly fixing the issue yourself and saving you some money in the process.
Long Fill (LF) or Drain Problem (F9E1) Error Code 1.Press the power button to cancel the cycle.
2.Unplug the washer or disconnect power to the outlet its using.
3.Turn the power back on and select the cycle you wanted and press start.
Washer Problem (F--E--) Error Code 1.Press power to end the cycle.
2.Open the door to check for excess water in the drum.
3.Press "RINSE DRAIN & SPIN" if there is still water in the drum to remove that excess water.

Suds Routine (SD) Error Code 1.Open the drum at the end of the wash cycle.
2.Remove the clothes from washer, carefully examining them for damage from the excess suds issues.
3.Review your detergent uses to ensure that you're using the recommended type of detergent and the correct amount as stated on the product's instructions.

follow this steps .God bless you
F/H No water detected entering machine or Pressure switch trip not detected.

If after 30 seconds the control does not detect water entering machine and then valves will be turned off and the error code will be displayed.
Or
If the control has turned the water valves on and after 8 minutes the flow meter has detected 10.5 gallons of water passing through it, but has not detected the pressure switch trip, the valves will be turned off and the error code will flash.
Press PAUSE/CANCEL twice to clear the display.

• If there is no water in the unit:
  1. Make sure that both valves at the water source(s) are turned on all the way.
  2. Check for plugged or kinked inlet hoses or plugged screens in the inlet valves
  3. Verify inlet valve operation
• If there is water in the unit:
  1. Verify Drain pump operation
  2. Pressure Switch Hose is in good condition and properly connected to Tub and Pressure switch
• Verify there is not a siphon problem
• Verify wire harness connections to:Inlet Valves, Pressure Switch, Drain Pump, Flow Meter, and Central Control Unit (CCU)
• Check all hoses for possible leaks

May be a water pressure sensor problem.
This tells it when the tub is full.
start with this video
https://www.youtube.com/watch?v=2pIVkAxWSXg

Hello,

The FH error code means the computer on the control board didnt detect any water entering the washer..sometimes it doesnt detect the water entering because the filter screens on the water inlet valve are clogged with sediment and water is having a hard time entering the washer.

The filter screens can be checked by turning off water at the faucets and disconnecting the fill hoses from the back of the machine and pop the scrrens out of where the hoses connect at the washer and check for blockage in them. If they are found to be clean check the water coming out of the hoses before connecting them back to the washer...if the screens are clean and water pressure is good out of the hoses the part of the washer called the FLOW METER would need to be replaced


GENE

Check this MAYTAG troubleshooting: Display shows F20 or FH - Front-load washer

Hope helps.

The error code FH means no water is detected entering the machine which can be due to a faulty flow meter not registering the correct amount of water that has passed through it or the pressure is not tripping from the empty position to the full position when the correct water level has been reached. Your machine is definitely made by Whirlpool like other Kenmore and Maytag washing machine so they are basically the same and troubleshooting is then the same. The link below contains the detailed troubleshooting of this error code for a Whirlpool Duet and should be applicable to your machine.

Error Code FH on Whirlpool-made Front-Load Washers

The F11 code means there is an electrical with the Maytag Epic washer. This could involve wiring, fuses or a number of other issues.

Press the "Pause" button twice to stop the current cycle. Press the "Drain" button to remove any excess water. Try to run the washer again. If the F11 code repeats, shut the washer off and contact a service agent
.
The FH error code may be mistaken for the F11 code. The FH code signals a water supply issue and has nothing to do with electrical problems. Check the LCD screen to ensure you read the proper code

go 2 repair clinic on line, same codes for whirlpool duet repair help then error code tab

my epic will start & wash & then gets F 20 & won't drain until I hit start again

ths.gardenweb.com/forums/load/.../msg1012004912002.html