Wont switch on

Hi,

Please switch to another mode - maybe power save mode before the machine has a chance to reach the point where it goes into sleep mode. Forcing the machine into another mode, should mean that it can't go into sleep mode.

Thank you.

I would check for a sticky drain or a sensor that has build up on it. These issues can be fixed with a little vinegar and a rag. Clean the build up off and see what happens.

it requires servicing

A fix from a forum:

Procedure 1 We found this procedure to work for the Stylus Photo 1270 type printer, and understand that it also works for the 870 range and even earlier models like the Stylus Color 740. The error is indicated on these printers by all four lights on the printer flashing. Even if you press the power switch on the printer, the lights continue to flash, and the printer does not turn off!

1. Turn off your printer, ensuring that the print head is at it's home location and locked in place as normal;
2. Power off the printer at the wall or by removing the power cable, for at least 20 seconds;
3. When you restore power to the printer at the wall socket or by reinserting the cable, if the lights come back on straight away, the printer's power switch was 'on' - switch it off and return to step 1;
4. Hold down the paper-feed button and the button with the ink-drops next to it, and then turn on the printer, still holding the buttons down;
5. When the paper-out LED flashes, release the buttons;
6. Press and hold the Cleaning button, until several lights flash - this will take a few seconds (i.e. then release the button);
7. The printer will now attempt to reset, including resetting the EEPROM memory and running a short (about 10 seconds) cleaning cycle.

Procedure 2

1. Turn off your printer, ensuring that the print head is at it's home location and locked in place as normal;
2. Hold down the paper feed button only;
3. Turn on the printer;
4. As the paper feed light starts flashing, release the button;
5. Immediately hold down the ink-drops button for some 10-20 seconds or until the printer springs into life;
6. Allow printer to complete it's processing, then turn off for a few seconds, and back on again for a newly working printer!

Procedure 3 - for 1290 and possibly 890 printers 1290 printer with green (power / data) and red (ink / paper feed) lights flashing alternately:

1. Switch off printer with panel switch;
2. Switch off printer at mains switch - leave off for 20+ seconds;
3. Hold down roll feed and sheet feed buttons;
4. Switch on at mains;
5. Switch on at printer panel;
6. Continue to hold down roll and sheet feed buttons until both green and red lights flash together in synchronisation, not alternately;
7. Switch printer off and then, after a few seconds, on again at mains switch;
8. When red and green lights are both flashing in synchronisation, release the roll and sheet feed buttons;
9. Press and hold down the ROLL FEED button (the one at the extreme left) and keep it down until the machine finishes whirring, cleaning etc and the green light comes on steady;
10. Release the roll feed button and all should be well.

My EWD1477 was doing this a year ago and I fixed it. Then it started doing it again a month ago and I seem to have cleared it again.

Firstly, remove the drain hose from where it is inserted into a laundry sink hole to make sure it is not blocked or sealed in with sludge.

Secondly, make sure the machine is empty of water and clothes and then turn the machine to off with the Program Selector Dial. Then turn off the power at the socket and remove the power plug and leave for five minutes.

Step 1: put the plug back in and turn the power back on.

Step 2: turn the selector switch to the right (Whites/Intensive). The green light of the Start/Pause button should be flashing and the green lights on for Prewash/wash, Rinses and Spinning. Don't press any other buttons or change any other settings.

Step 3: press the Start/Pause button and wait for the machine to empty any excess water. Press it again immediately after you hear water flowing into the machine OR two audible clicks. The machine is now in pause mode with the green light of the Start/Pause button flashing. Only the green light on the Prewash/Wash button should be on. Leave it in pause mode for 30 minutes and then press the Start/Pause button to recommence the cycle.

Step 4: If the Start/Pause button begins flashing, water stops flowing into the machine and the three green lights mentioned above are back on, turn the Program Selector Dial back to off, wait 10 seconds, and repeat the process above.

Step 5: If when you then turn the Program Selector Dial to Whites/Intensive and hear the two audible clicks, immediately press the Start/Pause button to set the machine in pause mode. Wait 30 minutes. Then press the Start/Pause button to recommence the cycle.

Hopefully the cycle will run without a problem.

Depending on what type of printer you have:

Procedure 1 We found this procedure to work for the Stylus Photo 1270 type printer, and understand that it also works for the 870 range and even earlier models like the Stylus Color 740. The error is indicated on these printers by all four lights on the printer flashing. Even if you press the power switch on the printer, the lights continue to flash, and the printer does not turn off!

1. Turn off your printer, ensuring that the print head is at it's home location and locked in place as normal;
2. Power off the printer at the wall or by removing the power cable, for at least 20 seconds;
3. When you restore power to the printer at the wall socket or by reinserting the cable, if the lights come back on straight away, the printer's power switch was 'on' - switch it off and return to step 1;
4. Hold down the paper-feed button and the button with the ink-drops next to it, and then turn on the printer, still holding the buttons down;
5. When the paper-out LED flashes, release the buttons;
6. Press and hold the Cleaning button, until several lights flash - this will take a few seconds (i.e. then release the button);
7. The printer will now attempt to reset, including resetting the EEPROM memory and running a short (about 10 seconds) cleaning cycle.

Procedure 2

1. Turn off your printer, ensuring that the print head is at it's home location and locked in place as normal;
2. Hold down the paper feed button only;
3. Turn on the printer;
4. As the paper feed light starts flashing, release the button;
5. Immediately hold down the ink-drops button for some 10-20 seconds or until the printer springs into life;
6. Allow printer to complete it's processing, then turn off for a few seconds, and back on again for a newly working printer!

Procedure 3 - for 1290 and possibly 890 printers 1290 printer with green (power / data) and red (ink / paper feed) lights flashing alternately:

1. Switch off printer with panel switch;
2. Switch off printer at mains switch - leave off for 20+ seconds;
3. Hold down roll feed and sheet feed buttons;
4. Switch on at mains;
5. Switch on at printer panel;
6. Continue to hold down roll and sheet feed buttons until both green and red lights flash together in synchronisation, not alternately;
7. Switch printer off and then, after a few seconds, on again at mains switch;
8. When red and green lights are both flashing in synchronisation, release the roll and sheet feed buttons;
9. Press and hold down the ROLL FEED button (the one at the extreme left) and keep it down until the machine finishes whirring, cleaning etc and the green light comes on steady;
10. Release the roll feed button and all should be well.

Hello,

• On some forums it is reported that you can make your NOkia 97 work smoothly (after a crash) without formatting it;
• Turn off your phone
• Connect the charger
• Remove the charger when the screen lights up and wait until it goes off.
• Turn on the phone immediately after using the Power button on top.
• After the vibration at start up, plug-in the charger.

For formating follow these Just follow the steps
Make a backup of contacts in your another sim.
Switch-off your phone.
1. Press and hold three keys at a time;it is called "3 finger reset" which is depress these three keys simultaneously "*" "3"

"green phone" and then power on phone whilst keeping those same three keys depressed until you see formatting.

If you dont understand, again follow the step.
You will use three finger for pres three keys ."green phone"+ "3" +star( *) and pres the power on switch.

All switch will be pressed at a time.

Soon an formatting text, will appear ,then stop pressing those switch,

Remember.
2. After a few minutes when the Full phone formatting completed, your phone will back to original system and factory

stetting.
Hope this helps.

it will not show anything. the power light is green.

Alright you need to put your ps3 in what is called "safe mode". First make sure there is no disc in the ps3, then turn off the ps3 in the back(main power switch), turn that switch back on, then hold the power button in front until you hear a total of 3 beeps, then let go, the light will be red, hold the power button again and you will hear 2 beep then a quick double beep, let go of power button and the light should stay green. A menu will appear, try all option working your way up from option 1 until it works. If you go through all 6 option and you are still having issues call 1-800-345-7669 to have your ps3 serviced

you can try following the steps from this vid http://www.youtube.com/watch?v=sWOrYLX01eA