I have a ws-a65 tried to install 1080 hd quality through At&t u-verse missing green and red color only shows yellows and blues help!!!

the problem is on the cables , look on the back of the cable box , if it is hd box the on ly thing you need to do is put the cables base on there colors green with green , red and blue , the other 2 are for video , but if it is normal box just put the yellow color with yelow on your box to your tv and the other to are audio

One side is standard, Other is HD. Red to Red Blue to White AND When you have Green it goes where Yellow would. Other Blue Would replace Green too. hope that helps. Pretty normal if your TV is HD Ready. Most DVD boxes are standard color coding. Try that.

Your Convergence ICs have likely failed. It is very common on rear projections. Replace the STK chips, check fuses and the resistors next to the STK chips. Replace as necessary and re-align via the service menu.


Use this simple test to verify.
Go to the users menu on the tv.
Look for the converge option to align the red and blue colors

If you cannot move the red either horizontal or vertical, then the STK chip has failed for red section.
If you cannot move the blue either horizontal or vertical, then the STK chip has failed for the blue section.

If you can move both in each direction then the problem is something else.


Note if one STK chip fails, you replace both regardless. There may only be one STK chip in this set. If there are two, they will be right next to each other.

use just the red green and blue wires for the picture and NOT the yellow wire. That is why it is messed up.

XBOX games only play in 720, but it will still look great.

2 things the cable could be faulty (unlikley)but worth a try
or your lamp is starting to fail

There is no "reset" as the set has in the customer and tech menus ways to attempt to manually adjust this.

under convergence in the customer menu select advanced and follow the instructions on the screen.


If Red or Blue or Green are skewed and will not adjust it means one of the two STK-394-250 CONVERGENCE chips this set uses is bad.

Depending on where you buy them they will range in price from about 12 dollars each to nearly 35 dollars each.

Let me know what you find; this may or may not be a do it yourself repair as some real expertise is required to correctly get at and replace the chips.

SD TECH

The front jacks are composite (yellow, red, white) I suspect x-box is component (green, blue, red)

Look for the one component input on the back marked DTV which should have 1080 marked on it.

SD TECH

Are you trying to plug in the yellow, red ,and white cables into blue, green, and red slots? If you are you cannot because those are for HD inputs only

needs to be hooked to the tv with either an hdmi cable or componet(blue/green/red.yellow/white/) also check the game on the back of the box. some games are only made for 480 and 720

First of all, is your blue "HD" light lit up on the front of your Uverse box?

If yes, then you're in HD

If No, you need to check your connections from Box to TV
1.Those Red-Blue-Green cables are for video only, they don't carry sound and shouldn't be connected to audio outs. Audio needs a seperate cable. Make sure your Red isn't on the audio out which is also red. Make sure your blue and green aren't switched with each other either. Check that at both ends.
2. Try an HDMI cable. It will carry audio and video together and it's one cord instead of 5.
3. What brand/model of TV is it? Is it an older projection TV? The HD tuner might be shot. The individual color tubes commonly fail after a few years.
4. Are you selecting 720p or 1080i from your TV's menu or from the Uverse menu? You'll need to set it through the Uverse box, not the TV.
5.Follow -Menu -Settings -Aspect Ratio to change to 720 or 1080. This should start an autotest which will scramble your picture for about 5 seconds, then bring you back to a menu asking you to keep settings or revert back settings. If you never see that question pop up, then your TV isn't supporting the HD, and you settings will be rolled back automatically. If the question does pop up and you can read it, select "keep settings" and press OK. Your blue HD light should come on the front of the box now.