Question about Fisher and Paykel Washing Machines

1 Answer

MW612 NZ FAULTY PUMP .... [CODES]

Pump blocked up, cleared but now stops before the rinse cycle begins.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Master:

    An expert who has achieved Level 3.

  • Fisher and P... Master
  • 745 Answers

Replace the pump most likely has burnt copper windings

Posted on Apr 21, 2018

Ad

6 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

prem mathew

  • 1294 Answers

SOURCE: Rinse water fills the washing machine when the spin cycle starts

Check your outlet filter, most likely it is blocked, preventing the water from draining out. Chk your pump too. Before this disconnect from the wall socket; and also check the pipe coming from the tub to the filter. Siphon out the excess water from inside the machine before you open the pipes.

Posted on May 18, 2007

gittos73

peter gittos

  • 247 Answers

SOURCE: Fisher & Paykel "clog Problem"

the water comes through 2 vavle 1 for washing and the other for rinsing more than likely that the rinse valve is down it will need replacing thats the more common fault for washers not rinsing

Posted on Aug 12, 2007

Krazytech

Franklin Ouchida

  • 725 Answers

SOURCE: washer go though all cycles but no spin

not a mechanical timer in this one..

Posted on Aug 30, 2007

Anonymous

  • 26 Answers

SOURCE: LG Intello 7KG Washing Machine

You may have some articles that made their way into the pump housing. Alot of times I see dimes get stuck in the ports of the pump, remove and check out thoroly and also check hoses coming to pump for little son of a gun articles that like to hide.

Posted on Apr 01, 2008

Anonymous

  • 1 Answer

SOURCE: LG WD-8013F wont spin

Hi deppgirl,
I checked the lint filter at the front bottom left hand side and it was full of junk.  Once emptied it worked a treat.  Pull the flap down and turn the large knob anti-clockwise and pull to remove.  Good luck.

Posted on Apr 22, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do you ascertain if its drain pump or faulty controller board causing a fault 37 on a gw612?


Read the answer in the link below first, but in your case it can also be a faulty or blocked diverter valve. If you are good with a multimeter check the resistance of the pump windings. It should read around 33 ohms. It is not uncommon for the pumps to cook themselves and you can smell and see the burned out motor. I hope this is of some help

http://www.fixya.com/support/t25754844-error_code_37_fisher_paykel_8_5_kg_front


Jul 24, 2015 | Fisher and Paykel Washing Machines

1 Answer

Siemens avantgarde washing machin stopping at rinse stage


Does the washer pump out the water after the wash cycle? If not then check the drain lines coming from the pump to make sure that they are clear. Your pump not pumping will cause the machine to stop working as well

Mar 23, 2014 | Siemens Washing Machines

1 Answer

Frigidaire FWT647GHSO when it gets to rinse first rinse cycle, it doesn't stop filling with water. It won't agitate or spin. It works well in the wash cycle, agitates and spins and advances


probably you've got something blocking the water pump from doing its job properly so check that the water pump is free running emptying all the water if not then there is a blockage in the pump normally ist a button, paper clip or other debris out of a trouser pocket eric

Dec 25, 2017 | Frigidaire Washing Machines

1 Answer

Machine will not go through the spin cycle


The pump is blocked or has failed.The pump needs to be cleared or replaced.

Feb 06, 2012 | Whirlpool Washing Machines

1 Answer

Will Only Rinse/Spin with little to no clothes in drum


sounds like unit is activating out of balance lever thats y it works with no load in it .possible faulty suspension rods making bowl move too much.out of balance lever is at back of inside bowl to the right. try adjusting back feet to make them about half an inch higher than the front feet .that will move the bowl away from lever giving more tolerence. see how u go please reply 4 more help

Mar 26, 2010 | Fisher and Paykel GWL11 Top Load Washer

1 Answer

Fisher and Paykal GWL 10 US - Stops before rinse


52. (00110100) Eco - Diverter Top-up Fault diverter valve made be stuck in half open position ,may be a mechanical obstuction or the wax filled solenoid that actuates it may be faulty .located under machine beside pump .

Jun 17, 2008 | Fisher and Paykel GWL11 Top Load Washer

1 Answer

Aeg 72630 update will not rinse during rinse cycle


If the drain lines were plugged, there may have been enough pressure on the pump to fault out. Make sure the sewer line is completely open, as well as the lines at the pump.

Jan 14, 2008 | Washing Machines

1 Answer

Kenmore two speed automatic washer top[ load


Can only be blocked or a blocked air trap. Regards Engineer

Jun 19, 2007 | Kenmore Elite 45986 Front Load Washer

Not finding what you are looking for?
Washing Machines Logo

Related Topics:

100 people viewed this question

Ask a Question

Usually answered in minutes!

Top Fisher and Paykel Washing Machines Experts

Gerry Harvey
Gerry Harvey

Level 3 Expert

1481 Answers

jimorris77

Level 3 Expert

411 Answers

peter gittos
peter gittos

Level 2 Expert

247 Answers

Are you a Fisher and Paykel Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...