At Fixya.com, our trusted experts are meticulously vetted and possess extensive experience in their respective fields. Backed by a community of knowledgeable professionals, our platform ensures that the solutions provided are thoroughly researched and validated.
Dishwasher working ok on last load, when dishwasher switched on the LCD shows the selected program and you can hear the motor trying to pump the water into the machine after 10 seconds the LCD display shows the above error message (AO1)and no water has enter the dishwasher...
we have checked the filter and also jiggled the water piupe but to no avail. HELP
Error message A01 means -Acqua stop operated due to a leak or overfill. Check if there is still water in the machine after it stop pumping. In case you still have water - your problem is with the pump or with a blockage drain line.
If there is no water in the machin, it might be a water level sensor issue - stuck physically in the high level position or become defective.
Try to reduced the water presure and leveled it up by the water entrance tap to the machine, it might solve your problem.
Goog luck !!
mine Indesit DFP 584 had the same issue today. tried tilting forward, it helped for a moment. the real issue was in the drain pipe - it was leaking. after checking the bottom of the machine i found door and on the door was a floating sensor. once the door was filled with watter, it linked the sensor and that is what causes the A:1 error code. hope this is helpful. L.mine Indesit DFP 584 had the same issue today. tried tilting forward, it helped for a moment. the real issue was in the drain pipe - it was leaking. after checking the bottom of the machine i found door and on the door was a floating sensor. once the door was filled with watter, it linked the sensor and that is what causes the A:1 error code. hope this is helpful. L.
You can't post conmments that contain an email address.
Couldnt find the book on my indesit dishwasher but tried dovi suggestion and it worked.A01 kept coming up. cleaned the filter and the arms. still now working. sounded like the pump was running but as soon as i put it on a cycle after a few seconds error message a01 came up. Tipped the machine forward about 70% tipped it back. Machine working lovely again now..
thanks dovi
Just fixed my DE73 with error code A501. Found it still running overnight, water on floor. Emptied machine of dishes. Tried to restart it a few times - A501 every time. Shut door of machine. Make sure you have a mop or something to soak up water in front of machine.Tipped it forward about 70 degrees. Water ran out through bottom of door (I think). Tried short programme with machine empty. Ran ok. There must be a sensor somewhere that registers water overflow in base of machine.
- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
Definitely, water drain time-out. Error code i20.
The pressure switch doesn't return to EMPTY (1-2) after two drain phases lasting 120 seconds.
Possible causes:
Drain circuit obstructed/blocked; drain pump
interrupted or jammed (foreign bodies); level
pressure switch blocked on FULL (1-3); hydraulic
circuit of pressure switch obstructed; wiring faulty;
circuit board faulty.
Thanks to your detailed description of failure I conclude that in drain phase (after starts drain pump) leaks water and causing a short circuit. I would thoroughly reviewed drain hydraulic circuit. If is alarm displayed and there is no water inside dishwasher then check heater and anti-interference suppressor.
Hi Kevin , it seems like you have debris clogging your sump motor . Remove the lower spray arm and remove the five T15 screws then remove the motor cover . Next with a wet vac clean all debris in motor . Make sure theres nothing under the float switch .
I too have the same problem with my dishwasher. Didn't know about the circuit breaker trick. Will give a try. My husband is ready to throw all our Samsung appliances in the trash. We don't recommend them at all. Re-modeled our kitchen 4 years ago and had all new Samsung appliances installed. What a mistake. In the 1st year we had 2 service calls on the dishwasher, 2 on the stove and 1 on the refrigerator. Have had many problems with the dishwasher. Have been in touch with the company but their approach is you bought it your stuck with it. Thanks for the trick to fix PE error code. I'm NOT getting it fixed. I'll use it till I can't use it anymore then go buy something else.
*#9998*289#
: Change Alarm Buzzer Frequency*#9998*364#
: Watchdog*#9998*523#
: Change LCD contrast - Only with version G60RL01W*#9998*746#
: SIM File Size*#9998*862#
: Vocoder Reg - Normal, Earphone or carkit can be selected*#9998*786#
: Run, Last UP, Last DOWNIf
the up Codes doesn't work, you should change *#9998* to *#0.
i.e. *#9998*523# change to*#0523#.
An other thing that will help is to remove your SIM card.
*0001*s*f*t# : Changes serialparameters
(s=?, f=0,1, t=0,1) (incomplete)*0003*?#
: unknown*0003*?#
: unknown *#9998*377#
: EEPROM Error Stack - Use side keys to select values. Cancel
and ok*#9998*427#
: Trace Watchdog*#9998*785#
: RTK (Run Time Kernel) errors - if ok then phn is reset,
info is put in memory error.*#9998*778#
: SIM Service Table*#9998*947#
: Reset On Fatal Error*#9998*872#
: Diag*#9998*999#
: Last/Chk*#9998*324#
: Debug screens*#9998*636#
: Memory status*#9998*544#
: Jig detect*#9998*842#
: Test ******** - Flash the screenligth during 10 seconds
and vibration activated*#9998*837#
: Software Version *#9998*228#
: Battery status (capacity, voltage, temperature) *#9998*246#
: Program status*#9998*9266#
: Yann debug screen (=Debug Screens?)
*#9998*9999# : Software version SP-unlock
SGH-600 (and also SGH-Sgh-600*2767*3855#
: Full EEPROM Reset ( THIS CODE REMOVES SP-LOCK!! )But
also changes IMEI to 447967-89-400044-0. (Doing this is illegal)*2767*2878#
: Custom EEEPROM Reset*These
codes have been tested with version FLD_2C6 G60SB03X of Samsung
SGH-600Samsung SGH-600 Unlock
Codes*#9999# : Show Software
Version*#9125# : Activates the
smiley when charging.*#0001# : Show Serial
Parameters*#0837# : Show Software
Version (instructions)*#06# : Show IMEI
had to call an enginer out, the problem was down to a faulty motor rota, to identify if e30 is this fault, rotate the drum (so the motor rotates) and try to start the m/c. if it runs ok you know to change the rota. hope this may help someone
Try to see if it flashes an error code, that could help identify the problem. Otherwise, if the problem is only with programming and not with the actual dishwasher, you might want to try replacing the program timer module.
Holavastoviglie AristonL73nduo mi segnaAO1 cosadevofare
×