Question about Sennheiser HDR 130 Consumer Headphones

1 Answer

Sennheiser HDR 130 with TR 130 transmitter not working.

I have sennheiser HDR 130 headphones with TR130 transmitter. The base is flashing orange led continuously and very fast. I cannot hear any sound in headphones like the headphones are dead. Any suggestions to salvage it.

Posted by Anonymous on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 38 Answers

If you twist the earpiece,one of them has two NIMH AAA batteries ,worth checking out if these are gone ,which is what happened to me.I was about to bin my rs130's and just stuck two new rechargeables and the earphones are working again!!!!!

As for $20 dollars from sennheiser for replacements!?!?!?
You should pick up two NIMH batteries for a couple of bucks on ebay or amazon.DO NOT USE ORDINARY BATTERIES!!!!!

Posted on Aug 07, 2012

Ad

5 Suggested Answers

Anonymous

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Anonymous

  • 9 Answers

SOURCE: Bad battery for my Sennheiser HDR 45 headphone

A replacement battery can be purchased from Sennheiser for $20.00.

Battery is: BA 151

Sennheiser Link:
http://www.sennheiserusa.com/newsite/productdetail.asp?transid=004146

Posted on Jan 15, 2009

Anonymous

  • 9 Answers

SOURCE: Bad battery

A replacement battery can be purchased from Sennheiser for $20.00.
Battery Part Number: BA 151
Sennheiser Link:
http://www.sennheiserusa.com/newsite/productdetail.asp?transid=004146

Posted on Jan 15, 2009

Anonymous

  • 1 Answer

SOURCE: sennheiser hdr 120 headphones no longer hold a

Twist the pad counterclockwise on the left earpice. You'll find the batteries underneath.

Posted on Mar 06, 2010

Anonymous

  • 2 Answers

SOURCE: my sennheiser hdr 130 has no sound even though it

This worked for me (this solution was posted on another thread). Unplug the base and take out the headset batteries. Wait 30 seconds. Reconnect. Turn on head set. I could hear immediately!

Posted on Jun 14, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Sennheiser HDR120 - missing transmitter / alternative OR replacement?


The system is working in the 860 Mhz range, so not that common. Most of the time it is cheaper to by a complete new system then to tray to buy components. Just keep looking in the thrift stores you find a transmitter for this headphone for a good price.

Jun 15, 2014 | Sennheiser HDR 130 Consumer Headphones

1 Answer

I have a huge problem with these headphones (the Sennheiser HDR 120)... and my wife bought two of them... They have great sound on the computer, but once the green light turns off on the base? There...


The volume of the sound source (Mac) must be sufficient, otherwise the transmitter automatically turns off. Turn up the volume on the Mac, and turn down the volume on the headphones. There is no way to disable the Automatic On/Off function of the transmitter.

I’m happy to help further over the phone at https://www.6ya.com/expert/jeremy_69f3cc28d95bf514

Aug 12, 2011 | Sennheiser RS 120 Consumer Headphones

2 Answers

My sennheiser hdr 130 has no sound even though it has lights on its based and it is connected to my t.v. what is the cause of this problem and the solution?


This worked for me (this solution was posted on another thread). Unplug the base and take out the headset batteries. Wait 30 seconds. Reconnect. Turn on head set. I could hear immediately!

Jun 13, 2010 | Sennheiser HDR 130 Consumer Headphones

1 Answer

My cordless HDR 130 Sennheiser headphones no longer charge. I have only had them for about four years. What do you think is going on?


The batteries are at end-of-life OR your charger has failed.

Forst replace the batteries... they are MOST likely bad. Charge the new ones before using.

Feb 02, 2010 | Sennheiser HDR 130 Consumer Headphones

1 Answer

Have a TR130. Unit is 5 plus years old. Original batteies


Being over 5 years, I know these batteries don't last that long typically. But even if you change the battery this problem still occurs, I see:
http://www.fixya.com/support/t2397503-sennheiser_tr130_headphones_hdr130

Get your multimeter and try measuring the battery voltage when they were out and when they were in with the thing turned on. If the volts don't change more than millivots (small), then it's not the batteries.
Check the REC OUT to make sure it's not set to PHONO it should be on SOURCE. You should be able to hear a little bit of static if it's normal.
Did you try changing channels? I thought the channel switch was a rotating knob, but it's not -- it's a push button that toggles from 1 to 2 to 3, and takes a few seconds to auto-fine tune on the frequency. Try changing the frequency and waiting five to ten seconds between button pushes to see what happens.

You really should get some new batteries if the above information doesn't resolve it, new AAA rechargeable batteries should.

Jan 13, 2010 | Sennheiser HDR 130 Consumer Headphones

1 Answer

No sound at all. The little green light is on the base. No sound from the earphones.


Actually, I didn't fix it. I thought I'd go to the shop where I bought it first.

Oct 31, 2009 | Sennheiser HDR 130 Consumer Headphones

2 Answers

No sound coming through my Sennheiser wireless headphones


Turning the transmitter on and off (Fig. 5)
Turn on the sound source. This automatically activates the
transmitter and the green LED “ON/OFF” lights up. If the sound
source is turned off, the transmitter is automatically deactivated
after approx. 3 minutes (the LED “ON/OFF” goes off).
Note: The automatic level control only functions if the volume of the
sound source is sufficient.

Mar 03, 2009 | Sennheiser HDR 140 Consumer Headphones

1 Answer

On/Off not lit when plugged in


There is help for this in the user manual. Possible solutions I would try:

1. Make sure your source sound (TV, amp etc) is up high enough - if the sound is too low the headphones won't detect a signal.

2. Try changing the channel (the switch on the bottom left of the cradle base) and pressing the "Tune" button on your headphones. Try all three positions, pressing "Tune" at least 3 times in each position.

3. Take out batteries & turn off base, leave for 30 secs, reassamble and try step 2 again.

Should all work ok. I've been using mine for over a year and they're great!

Feb 06, 2008 | Sennheiser HDR 130 Consumer Headphones

1 Answer

Sennheiser RS 130 Wireless Surround Sound Headphones


Did you try to remove the batteries and at the same time unplug the power of the base for 30 sec ?

Jan 10, 2008 | Sennheiser HDR 130 Consumer Headphones

2 Answers

NO SOUND HDR 130


Try to remove the batteries and at the same time unplug the power of the base for at least 30 sec. then replug and reinsert the batteries. That did the trick on mine.

Dec 25, 2007 | Sennheiser HDR 130 Consumer Headphones

Not finding what you are looking for?
Sennheiser HDR 130 Consumer Headphones Logo

1,973 people viewed this question

Ask a Question

Usually answered in minutes!

Top Sennheiser Audio Players & Recorders Experts

Michial Gueffroy

Level 3 Expert

1140 Answers

Rob Beech

Level 2 Expert

63 Answers

Geoff

Level 3 Expert

562 Answers

Are you a Sennheiser Audio Player and Recorder Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...