Question about RCA F27450 27" TV

1 Answer

My toshiba tv wont turn on

At first, it would turn on, no picture, and then turn back off. Now, I unplugged it, waited for a few seconds, and now it won't even turn on at all!! It is a Toshiba 42 inch flat screen model # 40E200UI

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    New Friend:

    An expert that has 1 follower.

  • Contributor
  • 1 Answer

FIRST GREEN LIGHT WOULD COME ON. TOOK IT AWHILE BUT ITWOULD FINALLY TURN ON...NO NOTHING. IT'S GETTING SPARK CAUSE WHEN I PLUG AND UNPLUG IT AT THE SOURCE OF ENERGY IT SPARKS. FUSE IS NOT BLOWN

Posted on Jan 08, 2013

Ad

6 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Anonymous

  • 61 Answers

SOURCE: TV Problem

The first thing is to check to see if the fuse is blown,if so replace with a 5 amp fuse,fuse is located near were the power cord connects to the board,make sure set is disconnected from power.

Posted on Mar 05, 2008

Anonymous

  • 3 Answers

SOURCE: phillips 27" flat tube tv

go to menu. u have a horazontel problem

Posted on Feb 07, 2008

bhur

roney trejeros

  • 85 Answers

SOURCE: 32 INCH tv

the cpu of your tv is not working,coldsolder the mainboard of your tv and the cpu then get the voltage output of your tv.

Posted on Jun 13, 2008

bhur

roney trejeros

  • 85 Answers

SOURCE: no picture, but power light is on

THE POWER SUPPLY OF YOUR TV WAS THE PROBLEM,YOU COLD SOLDER THE MAINBOARD OF YOUR TV,AND THE CRT SOCKET CONNECT TO THE TUBE IS ALSO COLDSOLDER,.

Posted on Jun 19, 2008

darjr

Darial Jr Lasaria

  • 379 Answers

SOURCE: RCA HD52W58 Picture not working / Sparking in back.

maybe there is a lizard inside, open the back cover then remove the PCB. re solder the damaged area and clean it with an electronic spray cleaner. check for cold solder component leads and re solder it.

Posted on Jun 11, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I replaced the lamp on 62530 worked fine for a few days, now the picture won't come on and the lamp light does come on.


unplug the unit wait 30-60 seconds & plug back in. Try unplugging your source at TV input & then plug it back in

Jan 03, 2015 | Mitsubishi Cooling Fan Set for WD-62530

1 Answer

No power when front button is press but on back of unit there is a flashing green light


Unplug the computer and wait for a few seconds. Plug it in again and press the power button. If this doesn't work, you will need to take it to a service agent as it won't be user repairable.

Oct 21, 2012 | Compaq SR5703WM -24407

1 Answer

Won't stay on


3-blinks by the SONY TV error code indicates that there is an audio circuit problem, ether is a shorted audio amp IC on the main board, or the power supply that supply the power to the audio amp section is defective.

May 22, 2017 | Sony KDL-52EX701 52 in. LED TV

1 Answer

Tv wont go past the start screen


I have the exact same problem and am seeking a solution too ... it won't boot past the Vizio logo on the screen and the remote and side buttons won't work :(

Apr 18, 2012 | Vizio L32 32 in. LCD HDTV

1 Answer

LG 32LH30 screen won't power up. Red light at bottom glows hi to low, but no picture. Unplugged and waited overnight, plugged in again, still no picture.


There is a way to tell if you have a bad board, or a bad panel.

1. Make the room dark and turn on the TV. Can you see it light up? If so, does it stay lit or turn right back off?

2. If the panel lights, but you have no picture, I would suspect the T-con. Some units now have the T-con incorporated with the main board, so you will need to check.

3. If you never get any light at all, then I would suspect the power supply.

4. If you only get light for a second or two, then you have a bad panel.

Apr 10, 2012 | LG 32LH30 32 in. LCD HDTV

1 Answer

My 42LD450 won't stay on! It turns on for a few seconds and works fine, then the screen flashes then comes back on, then flashes again after a couple seconds, then turns off. Rinse and repeat. Tried...


I hope that you can use the warrantee.

Otherwize, it must be possible to repair it with a fried comfortable with electronic because the problem is not permanent. This kind of problem is usually an old capacitor or a bad connection (soldering).
It would be important to check if changing the ambiant temperature fixes the problem. (I.E. move it to the seller for 2h and try..)

Regards,

Jul 10, 2011 | LG 42LD450 42 in TV

1 Answer

Bosch Nexxt 300 has error code E-13 and the door is locked. turned on/off, unplugged, removed the drain hose to see if it is blocked, but ok. but still won't unlock. Is there someway to unlock the...


Turn the dial to off position wait few second, door should unlock. Unless you try to open it during cycle, it won't open. Otherwise, follow owner manual. call the manufacture.

May 18, 2011 | Bosch Washing Machines

1 Answer

Turns off after a few seconds


The unit is going in to shutdown. There is a short in the unit. My guess would be the HOT and or Flyback are bad.

Jan 05, 2007 | Panasonic PT-47WX51 47" Rear Projection...

Not finding what you are looking for?
RCA F27450 27" TV Logo

154 people viewed this question

Ask a Question

Usually answered in minutes!

Top RCA Televison & Video Experts

The Knight
The Knight

Level 3 Expert

76204 Answers

matt martin
matt martin

Level 3 Expert

1257 Answers

Cindy Wells

Level 3 Expert

6063 Answers

Are you a RCA Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...