Need help fixing

Reciever RCA RT2500 ' Techlore

www.techlore.com/forum/thread/11889/reciever-rca-rt2500

Aug 20, 2005 - 31 posts - ‎23 authors
hey ive got the rca RT2500 home theater system. .... won't power up) regardless of number of times I try to simulate a 120 V power flash (pulling plug .... My RCA receiverturns on but there is no sound...what can this mean?

Trouble getting sound from home theatre system with my ...

www.tomsguide.com/.../trouble-sound-home-theatre-system-appreciated....

Mar 27, 2013 - TV: Sony Bravia KDL-60EX645 Home Theatre System:RCA RT2906 ...-I've set the television, per the manual's instruction, to "Audio System" and "Audio Out: Fixed." This should allow the TV to turn off its internal speakers and switch .... SolvedI have F & D home theatre system, my rear speakers won't work.

Problems connecting surround sound to LCD TV... - Forums - CNET

www.cnet.com > Forums > TVs & Home Theaters

CNETJul 30, 2006 - Hey I have a 26" LCD TV from Polaroid and a Philips DVD home theatersystem. ... the Audio setup on the tv and TELL it to output the sound via the RCAcables ... However, you would normally turn off the TV speakers with a menu ... I just can't figure out why the TV audio won't play on the surround sound. Anynet+ - Home theater won't turn on with tv
Jun 11, 2015
TV won't turn on
Jun 10, 2015
Audio Return Channel Problem
Aug 23, 2011
rca tv no sound?????
Jan 1, 2006
More results from www.cnet.com

check power inlet outlet

Appears that you have a bad cap in the power supply that is changing value as it heats up. Hard to find - only thing you can do is go to suspected units and replace them hoping that you got the bad one. Or just wait till it finally pops.

try video reset

when ps3 is in standby mode(red light)
press and hold the power button till you hear a second beep.

standby mode press hold power........"beep"......"beep"..release power button

then try rebuilding the database and the file system in recovery consol

to get to the recovery consol press and hold the power button when ps3 is in standby mode(red light) till you hear a double beep. sometimes the ps3 does a beep then another beep and goes back into standby thsi is fine just release the power and quikly press and hold it again till you get double beep.

like on my 80g system it goes like this

ps3 standby...press hold power.......beep .........beep........stanby again....release and hold power again.......beep .........double beep...release power now you should be in recovery menu.

power supply problem.can you open the circuit board.

Hello. There are a few causes for this. I will list acouple solutions for you.

1. Reset the Video Output Settings. While the PLAYSTATION 3 system is in standby mode (red light on the front of the system), hold down the touch-sensitive On/Off button on the front of the system until the system goes into standby mode again . (So the light cycle would go from: red light to --> green light --> then back to red light) This will ensure that you have held down the On/Off button long enough to reset the Video Output Settings. Once you turn it back on, it should work fine.
2. If option 1 does not work call Sony because the video out chip has blown or come unsoldered.

I hope this helps. Good luck to you.

I had a similar problem when there was a power outage or the lights went briefly out. I unplugged the TV and left it for a few days/weeks and then plugged it in and the TV worked. I think newer TVs should be treated like a home computer and put them on surge protectors.

Could be a power board problem. Anyone home at that time alone, possible internal damage due to spillage???? Pull harddrive, reseat memory and pull battery and try again.

Good day.

It is an internal problem particularly in the power supply section. But you can try checking on the fuse. It may have been blown.


chris

I have this exact problem, it appears the power on/off switch no longer works. After re-setting by unplugging the unit, use the remote only. As for the display, I find that if I turn the home theatre on last, the unit works and if I turn it on first, it behaves as you described.