Paper Jam in rear top roller has no physical access to remove paper jam in Kyocera Mita FS1900. Is there a special way to remove it?

To remove a paper jam from the exit rollers of a printer, you'll typically need to access the jammed area by opening the printer's covers. Keep in mind that the process can vary depending on the printer model and brand. Here are general steps you can follow to remove the cover and access the exit rollers:

1. Power Off the Printer: Before attempting to remove any jams or open the printer covers, make sure to turn off the printer and unplug it from the power source to avoid any risk of electrical shock.
2. Open the Printer's Top Cover: Most printers have a top cover that can be easily lifted to access the internal components. Look for a latch or release button on the printer's top cover and gently lift it up to open.
3. Locate the Jammed Paper: Once the top cover is open, carefully inspect the printer's internal area, especially around the exit rollers, for any visible jammed paper. If you find the jammed paper, gently grasp it and pull it out in the direction of paper movement to avoid damaging the printer.
4. Check the Rear Cover (if applicable): Some printers have a rear cover or panel that allows access to the exit rollers and other internal components. If your printer has a rear cover, you may need to open it to clear the jam completely.
5. Remove Paper Trays (if necessary): If the jammed paper extends into the paper trays, you may need to remove the trays to access and remove the jam more effectively.
6. Clear Paper Path: Ensure that all remnants of the jammed paper are cleared from the printer's paper path. Check for any small pieces of paper that may have torn during the jam and remove them as well.
7. Close the Covers: After you have successfully removed the jam, close all the printer covers securely. Make sure they are properly latched to ensure the printer functions correctly.
8. Power On the Printer: Plug the printer back into the power source and turn it on. Perform a test print to verify that the paper jam issue has been resolved.

Hi

Check all the paper movement from the tray, left or right cover, front cover, if so then remove jammed paper. Otherwise the paper sensor spring guide missing or fell off from its original position. Check carefully where the sensor locate. paper sensors detect all the paper movement in the machine during copying or printing, so locate the place in the machine which the paper usually jammed, see the screen of the machine, it will locate the place where the paper jammed mostly. Sensor not return to it original position that is why ( remove paper jam keeps blinking)

This usually means that no paper has been fed from the paper cassette or the machine was turned off when you had a paper jam.
Remove the paper cassette from the machine and ensure that nothing is stopping the paper from feeding.Also look into where the machine locates in the copier to ensure that no paper is jammed behind the cassette.
The paper feed rollers may need cleaning or replacing.

Do you mean that it is always jamming in the Document Feeder on the top of the copier?
If this is the case, I would like to know how far the paper goes in?
If it does,nt move at all, then lift the top plastic cover that sits above the paper. This will lift up and give you access to the paper pickup rollers. If you dont see any paper jammed, give the rollers a good clean with a clean cloth dampened with warm water.

Try cleaning the paper feed rollers for that cassette. Sometimes the rollers get dirty causing the paper to slip and not feed from the cassette causing the machine to register a paper jam.

The rollers can be cleaned with rubbing alcohol and a cloth.

make sure you don't have any small pieces of paper stuck in the printer
Paper jams can be real or false. The unit may report a paper jam when there is not any jammed paper, however, the solution to a real paper jam or a false paper jam is the same. WARNING: Jammed paper must be removed using the rear access door and the power cord must be disconnected or a carriage jam or mechanical damage may occur. Do not remove jammed paper from the front of the unit.

1. Turn off the HP product and turn it so the back of the unit faces you.
2. Disconnect the power cord from the back of the all-in-one. The power cord must be disconnected to allow the paper feed rollers to turn freely.
3. Locate and open the rear access door by pressing in on the left side tab and then pulling the door toward you. Figure 1: Removing the rear access door Inspect the pressure rollers on the rear access door and verify that they are clean and turn freely. Clean the rollers if needed with a soft towel lightly moistened with water. If the rollers do not turn freely, replace the rear access door.
4. Inspect the pressure rollers on the rear access door and verify that they are clean and turn freely. Clean the rollers if needed with a soft towel lightly moistened with water. If the rollers do not turn freely, replace the rear access door. Click How to buy on this page to order replacement parts.
5. From the rear access door opening, remove the jammed paper.
6. Remove the remaining paper from the paper supply tray. Discard any paper that is damaged or crumpled and then re-stack and reload the paper into the paper supply tray.
7. Reinstall the rear access door.
8. Reconnect the power cord to the unit and turn the unit on. If a carriage stall occurs after clearing the paper jam, resolve the carriage stall.

If you are not seeing any paper there you most likely have a bad paper detect sensor. The paper detect sensor is what looks for the proper timing of the paper moving through the machine and indicates a jam when the paper stops.

On most Kyocera Mita copiers a J-11 code indicates a possible paper jam when paper is being fed from drawer #1, but sometimes a J-11 will be indicated when the paper fails to feed from the drawer. Check the paper stops and paper guides in the drawer and make sure that they are flush against the paper, also cleaning the paper feed and pick-up rollers with a rag dampened with just plain water will help sometimes unless the rollers are completely worn out. If all this doesn't help you may have a paper feed clutch or lift motor that has failed.

Follow these steps to clear paper jam

Clearing paper jams
Paper jams can be real or false. The unit may report a paper jam even when there is no jammed paper. The solution to a real paper jam or a false paper jam is the same.
CAUTION:
Jammed paper must be removed using the rear access door with the power cord disconnected to avoid mechanical damage. Do not remove jammed paper from the front of the unit.

1. Turn off the HP product and turn it around so the back of the unit faces you.
2. Disconnect the power cord from the back of the all-in-one. The power cord must be disconnected to allow the paper feed rollers to turn freely.
3. Locate and open the rear access door by pressing in on the left side tab and then pulling the door toward you.

Figure 2: Removing the rear access door

1. Inspect the pressure rollers on the rear access door and verify that they are clean and turn freely. Clean the rollers if needed with a soft towel lightly moistened with water. If the rollers do not turn freely, replace the rear access door. Click How to Buy on this page to order replacement parts.
2. From the rear access door opening, remove the jammed paper.
3. Remove the remaining paper from the paper supply tray. Discard any paper that is damaged or crumpled and then re-stack and reload the paper into the paper supply tray.
4. Reinstall the rear access door.
5. Reconnect the power cord to the unit and turn the unit on.

Preventing paper jams
The following information will help prevent paper jams from occurring:

• Never use paper that is torn or wrinkled.
• If you are having problems using paper that has already been printed on once (recycling), replace it with new paper.
• Remove and then reinstall the rear access door. Verify that the access door is fully locked in place. The paper can skew if the rear access door is not locked.
• Every six months to one year, clean the paper feed rollers with a rag lightly moistened with water. Over time the paper feed rollers accumulate dust and do not function as well as they once did.
• When printing envelopes, tuck the flap into the envelope and crease the folds before printing.

That is the problem, machine will show printer jam if paper feed rollers fail to pick up paper when requested, your machine sounds like it needs new paper feed roller or you can clean the paper feed roller with a slightly! damp cloth.

If no jam light shows when power is turn on and machine comes to ready and then you send a job to printer and it then shows jam then it is the feed roller or sometimes the feed clutch

If on the other hand it always show jam then there is or a switch is stuck.