Question about Frigidaire GLTF2940ES Front Load Washer

1 Answer

Tearing my clothes, putting holes in towels, etc

I have a top loader, still under warrenty, had 2 agitators put in, still tears the clothes badly. Frigidaire, won't answered my e mails, Best Buy
said they can not replace, cause it still works. Help. My clothes are
disappearing. My washer is CER 3600 AS1, I understand the agitator has been taken off the market, Palmer

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Frigidaire Master
  • 6,289 Answers

Call Frigidaire and keep asking for someone higher up until you get results.

Posted on Nov 07, 2017

Ad

6 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Anonymous

  • 83 Answers

SOURCE: Frigidaire Top Load Washer Won't Agitate FWS645GFS1

Sounds like something slipping or an actuator to the transmission not functioning fully if it cannot take a load. Not all machines use belts but rather direct transmission via gearing etc.
Something may be worn in the transmission.

Posted on Sep 15, 2008

Anonymous

  • 16 Answers

SOURCE: GE front loader keeps tearing clothes

You are overloading if that is all that it happens .....less clothes more water and set the cycle for delicates...... unless the clothes are coming out stuck around the agitator than thats a different prob....

Posted on Jul 22, 2009

Anonymous

  • 1 Answer

SOURCE: GE model number WCVH6600HWW with a huge tear

I have the same problem and I'm thinking of trying to replace the boot myself. I found this at ehow.com. The instructions and pictures seeem pretty good.

http://www.ehow.com/how_5651102_replace-front-load-washing-machine.html

Posted on Dec 11, 2009

apart4u

apart4u

  • 213 Answers

SOURCE: LG Washer leak, small tear in door seal

Follow these steps to replace your door seal:
Disconnect all power to the machine first!!


1 Locate the outer clamp band securing the seal to the door rim on the washing machine and examine it carefully for holes or tears. Many can be prised off with a flat-bladed screwdriver they have a spring system holding them, but some have a tensioning arrangement that has to be loosened.
2 After removing the outer clamp band, locate the inner one securing the seal to the drum and establish how this is secured. It may be necessary to loosen a clip, or you may be able to prise the band off with a flat-bladed screwdriver. Some are like very large Jubilee clips that you have to undo usually from the top.
3 Once the clamp bands have been removed, use both hands to pull the seal away from the inner drum rim. Some machines have a water spout holes that will have to be lined up. Others have a drain holes.
4 Rubbing a drop of washing up liquid into the groove on the door seal/gasket that locates on the drum makes fitting the new seal easier.
5 the new washing machine door seal should be fitted by locating the drain holes at the bottom of the seal first then push it on with both hands working opposite directions towards the top. This is quite hard if you have never done it before.
6 refit the inner band remembering this must be tensioned correctly for it to be water tight.
7 now fit the outer band and the test the machine for any leaks,

All washing machine spares featured in this article are available at apart4u with more video help in our tutorial section.

Information provided is a guide only. aPart4u accepts no liability for any problems occurring whilst attempting any advice shown. If in any doubt about fixing your appliance, always contact a qualified repairer.

Posted on Jan 19, 2010

Linda74

  • 70 Answers

SOURCE: miele front loader rubber door sela has small tear

No.
At the beginning of every cycle water enters appliance via top of door seal this is connected to the inlet water supply

Posted on Jul 08, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My Maytag washer ripped my clothes. They have holes in them, What could be the cause


If it is a top loader it is the clothes getting pinched at the base of the agitator. Undo the knob on top or the bolt under the fabric conditioner container, lift off the agitator, check underneath, and replace it, making sure it is seated well

If it is a front loader, I had the same problem and it needed a new drum. The ridges around the drum had some sharp bits that were cutting and tearing the clothes as the clothes were sliding over them.

Nov 14, 2016 | Maytag Washing Machines

1 Answer

I keep getting clothes wrapped in the fin of my GE washer.


The problem is wear in the fins and bearings. Replace the whole rotor assembly and bearings or buy new machine. Can I suggest a front loader

Nov 03, 2014 | Washing Machines

1 Answer

Does anyone else have trouble with whirlpool washer model wtw4800x02 grabbing and tearing clothes


check the agitators are secure in the drum and carefully check the inside of anything jammed in the drain holes. best to use a torch and wooden spatula than fingers just in case its sharp

May 09, 2014 | Whirlpool Washing Machines

1 Answer

Frigidaire Affinity Front Loader Washer


Check if there is any gap or if the bearing are worn on the agitator, check by pushing the agitator for any play. If so the bearings must be replaced,

Sep 26, 2012 | Frigidaire Affinity FAFW3511KW 3.5 Cu. Ft....

1 Answer

My towels are coming out of the wash frayed and coarse. My lighter cottons are all stretched out. What is causes this to happen and how do I repair it.


Hi

If your washer has developed a bad habit of snagging and/or tearing your clothes; before scrapping your washer, try these few tips:

1) Check, by hand, the smoothness of your washer. Look for any broken fins or roughness on the basket surface. Replace, if necessary.

2) Reduce the size of your loads. Heavy, cramped loads can cause a lot of friction which leads to tears.

3) Reduce the amount of bleach used. Bleach can eat holes in clothing.

4) Verify water level is not too low, especially during rinse cycle, where snags are more apt to occur.

5) Consider placing delicates in a garment wash bag

6) Front load washers have no center agitator, so they are less likely to tear clothes.

Please get back to us if you have further query or else please accept the solution.

Thanks for contacting fixya.com

Sep 16, 2011 | Washing Machines

1 Answer

My problem is the agiator tears my clothes what is wrong this does not happen everytime just sometime and ravels towels?


Perhaps you need to remove the agitator and look under it for objects that do not belong.
In the past I have found items of clothing and such.

Cabrio service manual


If you need further help, reach me via phone at https://www.6ya.com/expert/dan_73bbd84fe1d95b61

Jan 29, 2011 | Whirlpool Cabrio WTW6600SBT Top Load...

1 Answer

Won"t spin or agitate. Makes a loud rattling noise


If this is a Whirlpool manufactured TOP LOADER (such as Roper, Estate, Kenmore, Amana, and Frigidaire), you may have a damaged or broken motor coupling. Whirlpool manufactured top loading washers use a motor coupling between the drive motor and gearcase (transmission) in place of a drive belt. This configuration is known as "direct-drive". The coupling can break through normal wear and tear. Washing frequent loads of heavy items and reduce the life span of the coupler. Common symptoms include the following:

1. No spin or agitation.
2. Washer will fill and empty.
3. Drive motor still runs.
4. Strange rattling, grinding or clicking noise during agitation or spin cycles as the drum sits still.

If your washer is exhibiting these symptoms, then its probably a safe bet that the motor coupling is bad.

The following link explains how to replace one:

http://www.fixya.com/support/r3574231-replacing_a_motor_coupling

The part number for a replacement motor coupling is inlcuded in the link I provided. Replacements can be purchased at any of the following websites:

searspartsdirect.com
appliancepartspros.com
pcappliancerepair.com
repairclinic.com

All these sites are reputable and offer great service with competitive pricing, so shop and compare. The first three sites I have listed also included helpful exploded view parts illustrations to assist you with locating and properly identifying any parts you may need.

If you have any questions, please post back with your complete MODEL NUMBER (located on a nameplate along the wash tub rim under the lid) and let me know. I hope this helps you.

Dec 17, 2010 | Kenmore 24032\24036 Top Load Washer

Not finding what you are looking for?
Frigidaire GLTF2940ES Front Load Washer Logo

Related Topics:

1,074 people viewed this question

Ask a Question

Usually answered in minutes!

Top Frigidaire Washing Machines Experts

Gerry Harvey
Gerry Harvey

Level 3 Expert

1481 Answers

J. Bradshaw

Level 2 Expert

121 Answers

Archie Ferrarini
Archie Ferrarini

Level 3 Expert

869 Answers

Are you a Frigidaire Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...