Printer working but page is blank after printing

Do you mean your Epson Printer Printing blank pages? The Epson printer printing blank pages due to wrong paper size, outdated printer driver, Empty ink cartridge, dirty print head, improperly installed ink cartridge, and more.

Follow the steps to fix the Epson printer printing blank page issue:

·Restart the printer
·Fill the empty ink cartridge and reinstall the new ink cartridge
·Update printer drivers. If you have done all the above steps but still the printer printing blank pages.

Then follow more steps to fix the Epson printer prints blank pages issue.

It would help to know what kind and model printer.

Some printers can get clogs and not print. Those mostly have "head cleaning" in the maintenance tab in the print setup screens.

Many printers have ink gauges, but they really don't measure how much ink is in the carts, it's easier for them to count how much ink has likely been used. Sometimes you actually run out of ink before the printer think you're empty, though mostly it's the other way around.

https://www.youtube.com/watch?v=mvgWn4pAKmM


https://www.youtube.com/watch?v=jKAxfHcDumY


Youtube videos showing ways to clean printhead in Epson L printers.

Sometimes your printer print blanks pages, if your printer is out of ink. You can check the quantity of ink in the status of the printer. Sometimes, your printer displays messages if it is out of ink. So if you are facing such issues, you need to refill the ink in your printer. Communication problem with the printer and computer is also a reason for printing blank pages.

Does it give you an error message of ink cartages being empty ? try to replace them .. if it is an all in one printer then try to copy from scanner and see if that works. also try printing a test page, if none of this works then probably you need a new printer.

Carefully check all the paper driveway and also cartridges: something is still on the way

tried re-installing the sortware or going into printer diagnostics in the start,control panel.
and it will run a diagnostic & try to print a test page, & clean the cartriges.
If not the printer's broke
Hope this help's

you need to change the print head ...

Hi there Error 50c

Regarding the Dell A940 "Error 50c"....the user guide doesn't seem to mention "Error 50c". They do, however, mention a "Cartridge Error" on page 52 of the manual. They claim this means that the printer has detected a short circuit (fuse/resister) in the cartridge. As you may or may not have noticed in the manual, this is what they recommend doing about it:

1) Press Power to turn the printer off.

2) Lift the printer cover/lid (scanner unit) until the scanner support holds it open.

3) Turn the printer on.
The ink cartridge carrier moves and stops at the loading position unless the printer is busy.

4) Remove the color ink cartridge.

5) Lower the printer (scanner unit) until it is completely closed.
If the error message displays again, replace the black cartridge with a new black cartridge.

If the error message does not display, repeat steps 1–3 and then go to step 6.

6) Reinstall the color cartridge and remove the black ink cartridge.

7) Lower the printer (scanner unit) until it is completely closed.

If the error message displays again, replace the color cartridge with a new
color cartridge.
If there is no error message (indicated by flashing lights), repeat steps 1–3 and then reinstall both ink cartridges.
8) Lower the printer (scanner unit) until it is completely closed.

If you get the error message again, while both cartridges are installed, replace both of the cartridges.

Basically, what they want you to determine is,....if the short circuit is with the "black ink" cartridge or the "color ink" cartridge and then replace the cartridge that has the problem.

You may have to buy a new cartrige.
Please all I ask is call back and just gave a vote, it will gave me some satisfaction to know am helping some one, so I will keep on helping.
All The Best: Pineworks

I am working on the same problem. While you will not like the
answer here it is for the canon mf6530. What is causing it
is the shutter over the laser is failing to open. There for
it blocks all exposer. A temperary fix is to carefully lift the
shutter and tape it open using black electrical tape. Then
try a few prints you should have an image if this is your
issue as it is mine. I do not recommending running it in
this condition very long. When I find the final answer I
will attempt to post it.