Console died on the pro form 785F

It seems like you're experiencing issues with your Pro-Form 580X treadmill. Here are some troubleshooting steps you can try:

Safety Key: Ensure that the safety key is properly inserted into the console. Treadmills typically have a magnetic safety key that must be in place for the treadmill to operate.

Circuit Breaker: Check if there's a circuit breaker on the treadmill. If it has tripped, reset it. This is often located near the power cord entry point.

Power Source: Verify that the treadmill is properly plugged into a functioning power outlet. Test the outlet with another device to make sure it's working.

Calibration: Some treadmills require periodic calibration. Check the user manual for instructions on how to calibrate your specific model.

Check for Obstructions: Ensure that there are no obstructions or debris around the belt or underneath the treadmill that might be preventing it from moving.

Lubrication: Treadmill belts may require lubrication. Consult your user manual for guidance on how to lubricate the belt properly.

Control Panel: If the control panel buttons are not responding, it could indicate an issue with the console or wiring. You may need to contact Pro-Form customer support or a technician for further assistance.

If none of these steps resolve the issue, it's advisable to reach out to Pro-Form customer support or a qualified technician for a more thorough diagnosis and potential repairs.

Likely you fried a fuse getting the jump.
check your fuses as well as your ground wire

seems like the voltage was to high and took out the console. a replacement console is needed

Assuming the power cord/charger is working and that the battery isn't dying. Contact someone at customer service at the number below...

Phone: 800-345-7669

How to reach a live person:
Just press 0

Hours of Operation:
Monday - Saturday 6am-8pm PT
Sunday 7am-6:30pm PT

Assuming the power cord/charger is working and that the battery isn't dying. Contact someone at customer service at the number below.

Phone: 800-345-7669

How to reach a live person:
Just press 0

Hours of Operation:
Monday - Saturday 6am-8pm PT
Sunday 7am-6:30pm PT

Dear Sir: I will help you, please do the following step: Instructions Things You'll Need

• Power supply
• Standard screwdriver
• Batteries
• Access to local fuse or circuit breakers, if necessary

1. • 1 Check to see if the Pro-Form device is properly plugged into a working, grounded power supply if none of the console buttons are working. Turn the device on and reset local fuses or circuit breakers if necessary; reset the circuit breaker switch on the base of the unit.
     
   • 2 Turn off the fitness device and unplug from the power supply if the console only shows zeros or the console buttons are not working. Use a standard screwdriver to open the battery compartment on the underside of the console. Pull out the old batteries and recycle, if possible. Replace with new batteries, using the old batteries as a guide for the size and type of batteries needed. Place the flat end of each battery against the spring inside the battery compartment and gently push the battery into place. Close the battery compartment and restore power.
     
   • 3 Press and hold the "Stop" button if the console is only flashing repeatedly, indicating that the device is in demo mode. Insert the console key and push the "Speed Down" button to turn off the demo mode on the unit. Remove the console key.
     
   • 4 Reset the console buttons if the incline is not working properly on the machine. Insert the console key and press one of the "Incline" buttons. While the incline is in the process of changing, remove the console key. Wait two or three seconds and re-insert the console key.
     
   • 5 Remove the console key and unplug the Pro-Form device if none of the above steps are resolving the problem with the console keys. Unscrew the three screws that hold the motor hood on the front of the device and pivot the hood off the machine. Find the magnet and small reed switch on the left side of the pulley. Turn the pulley until the magnet is aligned with the reed switch and the gap between the two is approximately 1/8 inch. Reattach the hood, screw into place and turn the treadmill back on
     

If you need further assistance, please reach me.

sincerely. God bless you.

E.CUADRA
MANAGUA, NICARAGUA. C.A

Disconnect your car battery for 30 minutes. Plug it back in.

Hey Chris,

the laptop has not fried, all you need to do is as below

1. switch off the unit,
2. Dicsonnect every thing conenceded to the unit even the power supply
3. Remove the battery.
4. Press and hold the power button for 40 seconds to a min.
5. Resonnect battery and power only, try to power on.

In case this does not work, please call the customer care and send the unit in for service.

You might be OK. It sounds like the power brick died. The power brick sends only 5v/12v DC power to the unit. You most likely have fried the power brick and I would recommend borrowing a friend's to test. This should resolve your issue.

Experience the same problem with my Zumo 550. Told by service advisor @ Radio World that this is a common problem. Unit needs to be charged on the DC charger occasionally. The motorcycle mount and car mounts, I was told, does not charge the battery on these units, but maintains a charged battery.