Dynex DX-E401 Router setup

If this router is brand new and has not yet been configured, try using "admin" (without the quotes) for the username, and leave the password field blank. Press the "OK" button; you should be directed to a welcome screen. From there, click "Run Wizard" and you should be taken to a screen prompting you to create a new password for the router.

If you found this solution helpful, please leave a positive rating!

The Manual:
http://dynexproducts.com/cms/documents/DX-E401%20User%20Guide.pdf

The default address of the router is 192.168.0.1. Type that address into a web browser on a computer connected to the network and it should bring up the login screen for the router. The default login for the router is Username: admin with a blank password. If you changed this, you will need to reset the router with the reset button and configure your entire network again to make changes.

Hi.

Ip address is: 192.168.2.1

click login and enter admin for the username. Leave the password field blank.

Hope this helps!

If you don't have the current password, you will have to press the reset button located next to the power connector port. This will reset it back to factory default settings. The you can access it with your browser:

To access the Web-based management utility:

1 Open your Web browser and enter the IP address of the router into the
Location (for Netscape) or Address (for Internet Explorer) field, then press
Enter. The default IP address of the router is 192.168.0.1

For example, type 192.168.0.1

After the connection is established, the logon screen opens.

2 To log in as an administrator, enter the user name of admin and leave the
password field blank (default), then click OK. The Web management Home
screen opens.

You can download the user manual at:
http://www.retrevo.com/support/Dynex-DX-E401-Routers-manual/id/8352ag821/t/2/

On the back of your router press and hold the reset button for about 10 seconds.
This will reset the router to factory defaults.

Open your Web browser and enter the IP address of the router into the Web Browser. The default IP address of the router is 192.168.0.1

After the connection is established, the logon screen opens.

To log in as an administrator, enter the user name of admin and leave the
password field blank (default), then click OK.

Dynex DX-E402 router, changing NAT settings(UPnP) to access x-box live. go to router settings web page for router, http://192.168.1.1/, enter user name and password to access settings page. user id is usually admin this also for password. under advanced settings click on forwarding. In listed sub-catagories click on UPnp. click enable. this should solve any NAT issues with X-box 360 signing onto x-box live. dynex dx-e402 was very easy to setup.

plz check by resetting the router

according to the manual that i have, the model if the router that you have, DX-E401, is just a broadband router and doesn't have wireless capability. if that would be the correct model of your device, there's no way that you can enable the wireless encryption since it doesn't have wireless capability. but if you are really using a wireless dynex router, follow the steps below on how to access the router's page and enable the security.

access the router's setup page by typing http://192.168.0.1 on the address bar of your web browser (i.e. internet explorer, firefox etc). by default the username is admin, then leave the password blank.
you will be prompted with the router's page, now go to the wireless settings and look for the encryption field and enbale wpa from there.

if you are not sure whether your router has wireless capability or if you are using another wireless router just give me the exact model and brand then ask me

ciao!

Reset the router, Theres usually a push button on the back of it to reset it's cmos back to default. Then the instructions included should work. If not, you can always use John the ripper (linux) or cain and able (windows) to crack into it.

No u don't leave it blank the password IS blank so u just type in admin for the user name and then type in BLANK for your password then after than u can change your password but he username remains then same.