Kyocera FS 4000 cassette error

some clue of 'make model (what it is)' helps, but here you go.


1:15
Installing the paper cassette on the FS-1061DN and FS-1041
YouTube · KYOCERA Document Solutions Europe 1 minute, 15 seconds
Apr 16, 2013
1:36
Installing the paper cassette on the FS-1220MFP, FS ...
YouTube · KYOCERA Document Solutions Europe 1 minute, 36 seconds
Mar 28, 2013 View all

Kyocera P6130cdn- "Cassette 1 Not Loaded" Message

Copytechnet https://www.copytechnet.com > kyocera-mita-copystar
Mar 31, 2021 - Re: Kyocera P6130cdn- "Cassette 1 Not Loaded" Message 3 small switches present. Press and hold 1 or more and check if motor turns on rear left ...

Cassette 1 Not loaded Error - Kyocera FS-4020DN
Apr 25, 2017
Miscellaneous Ecosys P6130cdn "Cassette Not Loaded"
Apr 20, 2022
Disable MP tray and for printer to use cassette 1 and cassette 2
Mar 24, 2021
TA351ci "no paper in cassette 1" - Copytechnet
Aug 1, 2022
More results from www.copytechnet.com

The "Cassette Not Installed" error message on the Kyocera Ecosys M6635cidn typically indicates a problem with the paper tray or cassette. Here are a few things you can try:

1. Make sure the cassette is correctly installed: Check that the cassette is inserted correctly and fully into the printer. There should be a click sound when it locks into place.
2. Check the paper settings: Make sure the paper settings in the printer driver match the paper size and type loaded in the cassette. You can check this in the print driver settings on your computer.
3. Check for paper jams: If there is a paper jam, the printer may think that the cassette is not installed. Open the printer and check for any paper jams or debris inside.
4. Reset the printer: Try turning off the printer and unplugging it from the power outlet. Wait a few minutes and then plug it back in and turn it on. This will reset the printer and may resolve the issue.

If none of these steps work, it may be necessary to contact Kyocera technical support for further assistance.

Hello,
the error Call Service 7410:xxxxxxx usualy is about the Drum Unit not fully inserted in the printer.
On the left side of the printer you will need to open the cover and push the Drum Unit in place.
After it clicks in place power off and on the printer.
Best regards.

The cassettes have little motors on them that lift the paper up to the rollers when it's closed. Make sure there isnt a bind on the plate that lifts the paper up. If there isn't you might need a lift motor replaced. This is a pretty common issue.

www.equipmybiz.com Skelton Business Equipment Houston Copiers

Make sure that the front and top covers close smoothly and fully. If the blue toner release arm is not fully to the rear the top cover will barely close. To reset the process unit you should remove it and then re-install it making sure it makes a good 'click' when you insert it.

The error indicates -

Engine PWB EEPROM error Detecting engine PWB EEPROM communication error.

Causes - Improper installation engine PWB EEPROM. Check the engine PWB EEPROM installation,
- Defective engine PWB. Replace the engine PWB

IF turning the printer off and unplugging then plugging back in and turning back on doesn't correct the problem I would suggest you contact an authorized Kyocera service center such as www.gfbm.net.

Try the feed tires in the tray first. More than likely the paper is not being picked up and causing jam message. The separation roller also has a hub on it to prevent a second sheet from feeding. Sometimes these start to lock up ,a little oil on the hub sometimes relieves some of the tension.

Hello, the code 7000 refers to the toner motor, but if you check my blog and there I have the full service manual. I hope you let me serve a Comment

http://tiototos.blogspot.com/ press click

check the toner on the left had side is a locking mechanism... make sure toner is in correctly and that switch is locked...

I’m happy to assist further over the phone at https://www.6ya.com/expert/norman_d2fa496dce30c65d

call service 2000:0045345