Question about Hoover AAA140 Front Load Washer

Open Question

Hoover hnf7167-80 not draining

Carrys out wash cycle then does not drain fully & so does not reach spin cycle. will not spin also if switched of 7 then put back onto spin cycle.

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Anonymous

  • 1 Answer

SOURCE: Draining & Spinning

I had a problem and when they took the back off. Underwire bra had got jammed through drum holes which stopped it spinning and water issues. I hope this might help.

Posted on Jun 07, 2007

Ad

Anonymous

  • 135 Answers

SOURCE: water not draing away and machine is not spinning

Empty your machine manually by lowering the drain hose into a bowl or bucket. Then remove the kick plate and check the filter for blockages.Before replacing try the machine on drain to see if the pump is running, if problem persists there may be a blockage in the pipe from the drum to the pump.

Posted on Nov 15, 2008

Anonymous

  • 135 Answers

SOURCE: our hoover ultra care 1300 large load washing machine spin fault

The most common cause of machines stopping mid cycle is not draining. Your machine should have a filter behind the kick plate at the bottom.
If this is not the case please post back for further assistance.

Posted on Jan 22, 2009

Anonymous

  • 13 Answers

SOURCE: Machine not draining

Can you hear the pump running just before the spin cycle, if so then I suspect a blockage in the filter or pump hose, If not and machine is quiet then it could be a faulty water pump or PCB board and you would have to call a technician.

Posted on Apr 13, 2009

Anonymous

  • 30 Answers

SOURCE: washing cycle is ok but wont spin

check carbon brushes on motor

Posted on Jun 09, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Washer won't spin


Good Day,
Your washing machine is fully automatic?
the washing cycle is normal?
if yes do the same maybe it will help you.
for the fully automatic washing machine mostly have drain pump, please check the filter of your drain pump, how? remove the cup of your drain pump like a ordinary cup, screw it clock wise or counter clock wise.
Remove drain pump filter and clean it, some hair pins, cotton buds or coins or any small item that coz of clog up.
if your washing machine dont have drain pump ,but fully automatic check the drain motor if running or not? how? open the back cover for top loader washing machine only, select spin cycle and press start to see the drain motor running? the drain motor is like a small box with small wire to pull the lever of the drain to remove water inside, if the motor running or pull the lever of the water pipe but water still inside the washing machine, remove the drain cup or cover and clean it or check if have coin or cloth inside that coz of clog or water stuck,
if the drain pump or drain motor is weak this is will cause and long time draining or totally not running the drain pump or drain motor and its cause of totally stop the cycle of washing machine in rinse time or spin time, because all fully automatic washing machine, after washing cycle the drain pump or drain motor must be on, to remove water before start the next cycle. rinse or spin cycle.

Nov 02, 2013 | Washing Machines

1 Answer

Door will not open have wash cycle


Switch off, put in spin/drain cycle and switch back on; check water is fully drained and then check filter. If not all drained, lower hose to ground level and drain to a bowl.

Apr 28, 2012 | Hotpoint Washing Machines

1 Answer

Hello I have a Maytag Washer Model A512 The machine goes through a regular cycle OK - However, it DOES drains the water out during the rinse cycle, but does NOT drain the water out during the spin...


The timer will always advance to the next program if the machine does not fully drain. There is ALWAYS a spin when draining the water out, there is only one pump and one motor. The waterlogged laundry maybe telling the timer that there is still water in the tub. Put the machine on "Spin" and cheat the lid switch into thinking that the lid is closed. Use a clothes peg or wide ended screwdriver and see if there really is a spin....

Apr 07, 2017 | Maytag Neptune MAH5500B Front Load Washer

1 Answer

My Kenmore 400 washer does the following. If I start a wash cycle it goes through entire wash cycle without draining ever, just washes until it ends. If I lift and close the lid when the timer gets...


lid switch stops machine from spinning when the lid is open, Make sure the lid is fully closed. Loose screws on the lids right side not holding metal arm properly, or the arm is not positioned properly (the end which is pointed down when the lid is open needs to be slightly farther away from you, towards the back of the machine, to actuate the switch fully: or the lid switch itself which is underneath the top,

Jan 03, 2018 | Kenmore Washing Machines

1 Answer

Hi David here.My washing machine carries out the cycle till it gets to rinse and goes no further.Tried putting it onto spin and drian but it tries to carry on but stops.,


You will need to see the voltages to the sections , the spin, the drain and then confirm if the voltage stops from the program controller or the motor by itself.
If program controller stops action , check all inputs, check thedoor switch, check the connections, check the board.
If not the error canbe the board itself.

Sep 29, 2010 | Bosch Washing Machines

1 Answer

Will not go onto final spin on its own


check drain hose lid switch ....plugged pump or drain hose last timer

Aug 14, 2009 | Hotpoint WMA48 Front Load Washer

1 Answer

GE washer will not go to spin cycle or drain.


Possible lid switch not fully engaged. It will no drain or spin if lid switch is not fully engaged. I would also check the drain line for pluggage.

Oct 22, 2008 | Washing Machines

2 Answers

Washing Machine not draining


I have just fixed the same problem. At the front - bottom right is the filter - you may have to remove the kick board on your fitted kitchen to see this - put a small dish under to capture water - unscrew half a turn - drain off all the water - then fully unsrew and pull out - I had money and treads from jeans blocking the filter - clean out, replace filter and fully tighten. My machine worked after this. - Steve

Nov 21, 2006 | Indesit W 123 Front Load Washer

Not finding what you are looking for?
Hoover AAA140 Front Load Washer Logo

Related Topics:

40 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hoover Washing Machines Experts

peter gittos
peter gittos

Level 2 Expert

247 Answers

Gerry Harvey
Gerry Harvey

Level 3 Expert

1481 Answers

Poppa Maddo
Poppa Maddo

Level 2 Expert

372 Answers

Are you a Hoover Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...