It was working fine until today . I've tried everything and am positive the document is flat against the glass . Could this be like the older copy machines that would need something inside cleaned ? I tried adjusting the brightness and contrast before scanning and it didn't help .
SOURCE: two black vertical lines appear on copy, pdf, and scan results
Good luck..
SOURCE: Lexmark X9350 will not scan or copy
Hi, have you had any luck repairing this? I also had this problem. I rang Lexmark support who, after 45min on phone, decided to send me a new machine. They did not want the old one back so I intend to try and repair it when I have time. I reckon the x9350 are prone to scan head problems as mine was making strange noises before it packed up and I have seen other reports of problems on various forums.
SOURCE: scanning/copying problem (Lexmark 6500 series x6575)
please just you scan the object to resuleasion in and dp is 600 to 12oo select and you scane object and aply print is dark is ok.
SOURCE: I need to clean the under side of the glass.
Cleaning the glass on what we call a "disposable printer" can be interesting. The simple process is to start pulling screws that appear to permit access to the scanner bed. For Lexmarks this generally involves an almost full disassembly of the machine. If you do get it apart be very careful not to let any dust or debris or solvents get near or on the scanner head, this will likely prevent it from properly calibrating and stop the entire machine from running. New all-in-one machines are generally designed so that if one function fails, the entire machine fails. I would say to just purchase a new machine, a repair bill will easily equal that cost and a novice repair job has a good chance of rendering the machine inoperable.
The operation flow of sending faxes is as follows.
Load the original on the platen glass or on the Automatic Document Feeder (ADF).
Platen Glass
Press the button.
Adjust fax settings as necessary.
Dial the recipient's number using the numeric buttons or coded speed dialing.
Press the button for color sending, or the button for black & white sending.
Note: Color sending is available only when the recipient's fax machine supports color faxing.
If the document was loaded on the Platen Glass, the following message will appear. Load the next page on the Platen Glass.
If you have only one page of document to scan, go to step 5.
Press the same button as you pressed in step 4b.
Repeat steps 4c through 4e until all pages of the document have been scanned in and then go to step 5.
Press the button.
To cancel sending a fax, press the button. To cancel sending a fax while it is being sent, press the button, then follow the instructions on the LCD.
Contrast is the degree of difference between light and dark. Increasing the scan contrast setting further blackens dark areas and whitens bright areas, whereas decreasing the contrast setting reduces the difference between bright and dark areas. You can adjust the contrast among three contrast levels.
Press the button.
Press the button.
Press the (left) or (right) button to select the contrast.
Pressing the (left) button decreases the contrast, and pressing the (right) button increases the contrast.
Press the button.
You can adjust the image quality (fax resolution) of the document you send. The higher you set the image quality setting, the better the output quality will be at the other end, but the longer it will take for the transmission. Adjust the image quality according to the type of document you are sending.
Press the button.
Press the button two times.
Press the (left) or (right) button to select the resolution.
STANDARD:
Suitable for text-only documents.
FINE:
Suitable for fine-print documents.
PHOTO:
Suitable for photographs.
Press the button.
Return to Start Faxing
Back to the Top of the document
Press the button.
Press the numeric buttons to enter the two-digit code (00 - 19) assigned to the number you want to dial.
Press the button for color sending, or the button for black & white sending.
Note:
* Color sending is available only when the recipient's fax machine supports color faxing.
* To cancel sending a fax, press the Stop/Reset button. To cancel sending a fax while it is being sent, press the Stop/Reset button, then follow the instructions on the LCD.
Important
The inner side of the Document Cover (white sheet) (C) is easily damaged, so wipe it gently.
If the glass of the ADF (A)
is stained with ink, correction fluid, or the like, black streaks may
appear on the printed paper when the document is loaded in the ADF. With
a clean, soft, lint-free cloth, wipe the glass of the ADF.
With a clean, soft, lint-free cloth, wipe the Platen Glass (D), the inner side of the Document Cover (white sheet) (C), the glass of the ADF (A), and the inner side of the ADF (white area) (B) gently. Make sure not to leave any residue, especially on the Platen Glass.
Cleaning the ADF
Caution
Be sure to turn off the power and disconnect the power cord before cleaning the machine.
1. Open the Document Tray.
2. Open the Feeder Cover.
3. With a soft, clean, lint-free and dry cloth, wipe off any paper dust from the inside of the Feeder Cover (A).
4. After wiping, close the Feeder Cover by pushing it until it clicks into place.
5. Close the Document Tray.
6. Reconnect the power cord then turn on the machine.
85 views
Usually answered in minutes!
×