Washing machine will not rinse after the wash cycle. Water is still in washer

Hi,

please power cycle your washer (ie restart via power outlet unplug and re-plug). After this, please rotate the dial 90 degrees counter-clockwise before attempting another wash . All of these actions to help reset/undo any issues with the washer. Otherwise, you might need to schedule a home diagnosis/repair.

Thank you.

If the washing machine does stop at the rinsing cycle and will not continue , It could have something to do with the machine's timer not working correctly . If the timer is broken or is not working it will have to be replaced to make sure that the machine can be able to run through the rinse cycle again.

are the filters clean

In the rinse cycle it will use cold only to rinse with.
You need to see how fast the water is going into the machine on rinse
Things that can effect slow fill, low water pressure, Faulty cold valve
water hose & valve filters clogged, Kinked hose

The typical cycle is;
fills to selected water level
agitates wash cycle
drains wash water
spins wash cycle
fills to selected water level on rinse cycle
agitates on rinse cycle
drains rinse water
spins final time
end of cycle

Hi,

If your washing machine will not fill, only hot or cold will fill or is slow to fill then read these tips. I have covered many of the things that can happen in these tips…


Washing Machine Problems No Water

Washing Machine Fix Washing Machine No Water

heatman101

All content © 2000 © 2009 Washerhelp

• Home
• About
• Contact
• Sitemap
• Forum
• Blog
• Search

> Home / Repairs DIY washing machine advice (part 8) Washing machine sticks or stops mid-cycle A very common fault on washing machines is when the program timer fails to complete the cycle and stops part way through. Many people blame the program timer for this but although it is a possible cause, there are many more likely causes for this fault. The program will stick if the heater isn't working, if the thermostat fails, if it can't fill up with cold water for the rinses, if it can't empty the water etc. There are too many possible causes of this fault to be able to give anything other than rudimentary advice. However, the common causes of a washing machine sticking that can easily be fixed are filling and emptying problems.
Check that the cold water supply is available to the washing machine, which is a common cause for sticking on rinses. If the washing machine appears to stop mid-cycle and isn't filling with water on rinses then see Washing machine won't fill with water (or no water goes into washing machine) before calling an engineer. If the washing machine can't drain the water out then it will stick on the rinses, or it will abort with an error code. If you can see water still inside the washing machine then check the following advice Washing machine won't empty water

All content © 2000 © 2009 Washerhelp

• Home
• About
• Contact
• Sitemap
• Forum
• Blog
• Search

> Home / Repairs DIY washing machine advice (part 8) Washing machine sticks or stops mid-cycle A very common fault on washing machines is when the program timer fails to complete the cycle and stops part way through. Many people blame the program timer for this but although it is a possible cause, there are many more likely causes for this fault. The program will stick if the heater isn't working, if the thermostat fails, if it can't fill up with cold water for the rinses, if it can't empty the water etc. There are too many possible causes of this fault to be able to give anything other than rudimentary advice. However, the common causes of a washing machine sticking that can easily be fixed are filling and emptying problems.
Check that the cold water supply is available to the washing machine, which is a common cause for sticking on rinses. If the washing machine appears to stop mid-cycle and isn't filling with water on rinses then see Washing machine won't fill with water (or no water goes into washing machine) before calling an engineer. If the washing machine can't drain the water out then it will stick on the rinses, or it will abort with an error code. If you can see water still inside the washing machine then check the following advice Washing machine won't empty water

that is either a problem with the timer , or with the cold water hose at the back of the machine, see the following:



I quote from : The cycle doesn't advance

The cycle doesn't advanceWhen the cycle doesn't advance, it's probably the timer or a cold-water supply problem:

It'sthe timer, if your washing machine fills with water and beginsagitating, but the timer never advances--or if the washer is in a spincycle and the timer won't advance. Then you need to replace the timer.

Itmay be a cold-water supply problem, if the washing machine fills withwater, agitates, drains, and spins, but then doesn't fill with rinsewater. See There's no cold water.

Hi this could means that you may need to replace the washing machine bearings. Once the bearings are bad, the motor overheats and it will automatically shut down after the first rinse.

Timonty from WashingMachineAdvisor.com