Question about GE WHRE5260E Top Load Washer

Open Question

The concrete block ge used to balance my tube came loose

GTWN4250DWS top load washer The concrete part of a block they used for Weight purpose? came loose from its mount what a mess?

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

mpservices

  • 190 Answers

SOURCE: GE WASHER SPIN OUT PROBLEMS

Sounds like the suspension for the drum is having problems - there are usually springs holding the drum up and acting as shocks - one of the springs may have come off during an unbalanced load.

Posted on Nov 22, 2008

Ad

Anonymous

  • 1 Answer

SOURCE: removing cover assembly on GE top load washer

Is your washer a GE Profile Harmony? Do you want to know how to take the top off or the top of the agitor (pulsator)? The top of the washer has four screws in the back top behind the screen once you unscrew them the front of the washer has two clips one on each side and you have to kinda tap it with your palm to get them to pop.

Posted on Jan 13, 2009

Anonymous

  • 4 Answers

SOURCE: GE washer won't agitate

I had this same problem with our GE top load washer.  I just needed to pull harder.  (Note: The agitator is held in place by about a dozen L-shaped clips in a ring around the agitator's base that will release more as you pull harder on the agitator.)  Everything from the base below the large fins on up comes out together.  Grab the shaft above the fins and pull slowly and hard. I had to take the entire tub out, lay it on the porch, put my feet inside of it, and pull the agitator assembly out.  I wasn't able to pull it out while it was still in the washer.  BE CAREFUL! DON'T **** IT OUT; that might injure your back; just pull out slowly and as hard as you can without hurting yourself.  I was able to get it out successfully, but I am currently stuck at removing the bell below the agitator.  Good luck!

Posted on Feb 28, 2009

Frank Meola

  • 512 Answers

SOURCE: GE top loading washer does not spin out water

The belt could be broken, if not. Unplug washer for 2 minutes, plug back in, open and close lid 7 times, this should reset electronic motor.

Posted on Jun 12, 2009

FixinFax

Leroy Elliott

  • 3085 Answers

SOURCE: GE WBSR3140DW Top Load Washer Repair manual

Check your local Appliance Parts Stores, they usually have racks of repair manuals.

Posted on Nov 25, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

F&P Aquasmart Washer keeps going off balance. Nothing i do seems to help.Trying to complete one load for over 3 hours. PLEASE help.


Hi can you please explain what you mean by going off balance, is the machine jumping ? about if so the concrete weight to stop it jumping has come loose in the on the top of the drum housing apart from that I can only wait for your response cheers eric

Nov 16, 2017 | Washing Machines

1 Answer

Why does it bump and bang out of balance?


I had a front loading washer (not Kenmore) that bumped, banged, and walked all over the floor. Called a service tech. The balancers are made of concrete and one of them was loose. Ended up making a mess as the balancer that was loose finally broke and we had chipped concrete dust everywhere. Not pretty!!! Ours was covered under warranty.

Jun 11, 2015 | Kenmore Washing Machines

1 Answer

How do I set water temperature for the rinse cycle?


I suppose you have looked at the owners manual, on the page below, it seems to indicate knob B. but it is unclear
GTWN4250DWS GE 3 9 DOE cu ft stainless steel capacity washer GE Appliances

Dec 24, 2014 | GE GTWN4250DWS 3.9 cu. ft. capacity top...

1 Answer

When washing towels the load starts banging...not overloaded and repair service can't find the issue.


sounds like a broken shock,or balance spring!! possibly loose concrete weight on tub

Mar 15, 2013 | GE WSXH208A Front Load Washer

1 Answer

My GE washer acts as though it is off balance but redistributing weight does not help. The surface is level and checked with a level. Any other ideas?


counterweight brick under the tub if it has broken the straps holding it in place it will make loud unbalanced tub sounds quick and easy fix

Oct 06, 2012 | GE GTWN4250DWS 3.9 cu. ft. Top Load Washer

1 Answer

Beko 510w


the beko washer sometimes the concrete balance blocks come loose and cause a banging noise unplug and take the top off check the concrete block on the top off the outer drum to see if it moves about tighten it up if loose then check the one down the front to see if louse

Sep 20, 2012 | Washing Machines

1 Answer

Maytag washer out of balance


First make sure on the machine that all adjustable legs under neath are touching the floor and it is level if all is good. THis could be a case that the weight that balances the machine inside is either loose or off this is a big steel weight or a concrete weight under neath the machine and behind its cover from the rear. This has to be opened up to see what it actually wrong. Please dont forget to rate my solution and leave testimonial this is how i earn my achievements . Thanks in advance

Apr 23, 2012 | Maytag Dependable Clean Top MAV5920EWW Top...

2 Answers

The drum spins wildly out of balance to the point that it wears away the hard white plastic shield at the front. Is there some alignment guide that may need to be adjusted


this is usually caused by uneven loads. if your sure the the loads are evenly balanced check under your washer for loose or dropped parts

Oct 23, 2009 | Whirlpool Duet GHW9150P Front Load Washer

1 Answer

Banging washing machine on spins


Hi. I don't know if your problem has been sorted yet, if it has not ,then it sounds to me llke the concrete balance weight is loose or broken

There are 2 of them, one in the top of the m/c, and one at the bottom, if either of them are loose, then that is your problem.

If loose, can be tightened up, if broken away from the drum then you have a major problem

Nov 16, 2008 | Hotpoint Aquarius WD63 Front Load...

1 Answer

Whirlpool LHW0050PQ Front Loading Washer VERY NOISY during spin cycle


remove the top access panel 3 screws in top rear.
now look around and push on the drum from top
it has suspension shocks and springs like your car they should resist any movements.
look/wiggle the concrete balance blocks , no cracks or loose.
inside the tub are the arm solid /not loose.
run it with the top open what do you see/hear and where
look under the rubber flap in front did anything get under the tub

Dec 29, 2007 | Whirlpool LHW0050PQ Front Load Washer

Not finding what you are looking for?
GE WHRE5260E Top Load Washer Logo

Related Topics:

781 people viewed this question

Ask a Question

Usually answered in minutes!

Top GE Washing Machines Experts

Marvin
Marvin

Level 3 Expert

85222 Answers

geapptech

Level 2 Expert

157 Answers

jimorris77

Level 3 Expert

411 Answers

Are you a GE Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...