Error code E22 ON MY non-digital front load tumble action washer

I have never ever seen a 'DO' code. All washing machine codes are E and 2 numbers, except for 'LOC' for 'Lock'..

https://www.searspartsdirect.com/diy/error-codes/washer-repair/1234598/kenmore-417-model-front-load-washer/0582

Try disconnecting from the mains supply for 15 minutes.

https://www.google.com/search?q=Kenmore+model+44082+error+code+%22do%22

..

The E22 error code on your Candy Condenser Tumble Dryer model GVS C9DCG-80 31100907 indicates a problem with the drainage system. This could be caused by a few different things:

1. Blocked drain pump: The drain pump may be clogged with lint or debris, preventing it from properly draining the water from the dryer. Check the drain pump and make sure it is not blocked.
2. Drain hose: The drain hose that carries the water from the dryer to the drain may be clogged or kinked. Check the drain hose to make sure that it is not blocked or kinked.
3. Drain filter: Make sure that the drain filter is clean and not clogged.
4. Control board: The control board manages the dryer's functions and if it's faulty it can cause the E22 error.

To reset the error code E22 on your model, unfortunately, it seems that your model doesn't have a reset button or an option button to reset it. The best course of action would be to contact the manufacturer or an authorized technician for further assistance on how to reset the code and troubleshoot the problem. They will be able to diagnose the problem and provide you with a solution.

Possibly motor overheating.

I assume from your comment that your old washer was a top loader. Yes, front loading machines typically have longer cycle times than top loaders. There are several contibuting factors... first of all, the wash action of a front load is to oscillate the drum back and forth as well as provide a slow tumbling motion whereas a top loader w/ agitator or impeller has a more aggressive action. The more aggressive action rolls and tumbles your clothes more often and therefore cleans faster. Also, because front loaders spin very fast (up to twice as fast as top loaders) to reduce the amount of moisture left in the clothes, they need to have balanced loads. They accomplish this by testing and rebalancing your load several times during each cycle before beginning to spin.

That was a long answer to your question- no, you are not doing anything wrong.

Good luck.

liquid is best as powder is mostly made of a "clay base" in its detergents??? yes i did say clay!

Mine was the door lock switch, $80. and about 20 mins. working like a champ.

I am not a repair professional. I am just a 78 year old man who has been making his own repairs for about 50 years. Therefore the washer ID doesn't mean
anything to me. It's been about 55 years since I had experience with front load washers. However I can refer you to Applianceaid.com where they have very good and complete trouble shooting and repair information on front loaders. I think you'll find what you need there. Don't worry about the timer, they hardly ever go bad. Good luck with it. If I have helped you, please rate my advice on fixya.

Hi hilary_allar,

It means that your motor communication is being lost. Generally on these LG washers it means that you need to replace the motor sensor. You will have to take the back panel off so that you can access the motor, remove the pulley and take the motor off, there is a little plastic sensor that clips onto the edge of the motor. The sensor is not sold separately from the motor so you will have to replace the motor unfortunately.

Try unplugging the machine for approximately 15 - 20
minutes. This will reset the microprocessor.

The LE error code can be an indication of several different issues.

The most common cause is over-sudsing in the machine. Many times owners
experiencing the LE error code are using regular detergent. It is recommended to
use a high efficiency or low sudsing detergent. Many of the leading detergent
manufacturers have a high-efficiency (HE) selection. The HE detergents are
designed for lower suds levels and enhanced cleaning performance in
front-loading washers.

Overloading the wash with too much laundry may also cause the LE error code. A
good rule is to load the washer until the clothes in the drum are no more than
three-fourths of the way up the window of the door. This will allow them
sufficient room for tumbling. The clothing having sufficient room to tumble is
more important than either the weight or the number of items in the washer. It
is the tumbling action that provides the washing effect.

Lastly, a breakdown in the signal between the microprocessor and the motor may
cause the error code. This can occur if there is a loose wire, dislodged ball
sensor, or if the shipping bolts are removed prior to situating the washer. . In
this case, a servicer would need to take a look at the unit.

Regards
R.K.

Hi reginaroney,

It means that your motor communication is being lost. Generally on these LG washers it means that you need to replace the motor sensor. You will have to take the back panel off so that you can access the motor, remove the pulley and take the motor off, there is a little plastic sensor that clips onto the edge of the motor. The sensor is not sold separately from the motor so you will have to replace the motor unfortunately.

Try unplugging the machine for approximately 15 - 20 
minutes. This will reset the microprocessor.

The LE error code can be an indication of several different issues.

The most common cause is over-sudsing in the machine. Many times owners
experiencing the LE error code are using regular detergent. It is recommended to
use a high efficiency or low sudsing detergent. Many of the leading detergent
manufacturers have a high-efficiency (HE) selection. The HE detergents are
designed for lower suds levels and enhanced cleaning performance in
front-loading washers.

Overloading the wash with too much laundry may also cause the LE error code. A
good rule is to load the washer until the clothes in the drum are no more than
three-fourths of the way up the window of the door. This will allow them
sufficient room for tumbling. The clothing having sufficient room to tumble is
more important than either the weight or the number of items in the washer. It
is the tumbling action that provides the washing effect.

Lastly, a breakdown in the signal between the microprocessor and the motor may
cause the error code. This can occur if there is a loose wire, dislodged ball
sensor, or if the shipping bolts are removed prior to situating the washer. . In
this case, a servicer would need to take a look at the unit.

Regards
R.K. 

I have a stacking Frigidaire washer/dryer. The dryer will not start at all.

Thanks for any info you can offer.