Dewalt Dw938 18v Reciprocating Saw Sawzall Recip 18 Xrp Logo

Related Topics:

A
Anonymous Posted on Oct 21, 2012
Be the first to answer

Why does my dewalt sawzall not hold a blade - Dewalt Dw938 18v Reciprocating Saw Sawzall Recip 18 Xrp

Answer This Question

2 Related Answers

Repair Ahjoshe

  • 885 Answers
  • Posted on Jan 31, 2011

SOURCE: DEWALT DW938 18VOLT CORDLESS SAWZALL can it use

As long as the voltage of the battery is the same as the tool, the tool won't mind if the power is coming from a NiCd or lithium battery. You do have to have a charger that works with lithium batteries to charge them up. Chargers that can charge lithium batteries can also charge NiCd and NMH batteies. NiCd chargers are not always programmed to detect when lithium batteries are full and may continue to charge them to the point of melting or starting on fire.

Ad

RSole

  • 697 Answers
  • Posted on May 06, 2012

SOURCE: broken blade in dewalt sawzall

Remove broken blade, install new one. These blades don't change themselves, unfortunately.

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

A piece of a broken blade is stuck here the blade fits into the saw (Dewalt DW 303m). How do I get it out?
Craig, a drop of penetrate oil and you will just have to work at it with ice pick.small screwdriver, or needle nose pliers if you can, make sure you have blade release depressed while trying to pry blade shank out. Once you get it moving it will fall out. Clean and blow out blade port before inserting another blade.
How to Remove Stuck Blade on Sawzall Hatchet eHow
Troubleshooting Your Malfunctioning Reciprocating Saw DoItYourself com
Read full answer
May 26, 2016 • Dewalt Saws
0helpful
1answer

Dewalt how to take apart
Remove the 3 screws holding the foot on and remove it.
Slide the insulator and blade clamp lever off exposing the gearcase.
At this point you can remove the gearcase from the handle and can access the entire tool.
Removing the gear assembly will require removing the nut (#18) at the front of the gearcase (under a plastic cover) (best done with a 13mm socket on an impact driver) then removing the blade clamp assembly allowing the mechanism to slide out.

24886363-pshsvhvr0p05awby03ee0agp-2-0.gif
Read full answer
Jul 29, 2014 • Dewalt Dw938 18v Reciprocating Saw Sawzall...
0helpful
1answer

Broken blade in dewalt sawzall
Remove broken blade, install new one. These blades don't change themselves, unfortunately.
Read full answer
May 06, 2012 • Dewalt Dw938 18v Reciprocating Saw Sawzall...
0helpful
1answer

The blades come out
The piece that holds the blade in is held in place by a spring that sometimes breaks. eReplacementparts.com has a diagram and sells the springs for 78 cents.
Read full answer
Apr 25, 2012 • Dewalt Dw938 18v Reciprocating Saw Sawzall...
0helpful
1answer

Replacing blade assembly on a dewalt 18v Reciprocating Saw Sawzall
Remove the foot, remove the boot (and yellow lever), pull shaft out all the way (so you have more room to work with), remove the spring clip from the clamp block, remove the lever and ball, the clamp block will then slide off once the wire clip that wraps around it is removed.
Read full answer
Apr 22, 2012 • Dewalt Dw938 18v Reciprocating Saw Sawzall...
0helpful
1answer

Have DeWalt Model 303 Type 1 Blade is stuck can not remove, removed Scew part # 99164-06. Blade is still stuck, blade will move side to side, back and forth but will not slide out. Any ideas
It sounds like the set-screw may have caused a burr on the blade, and that's preventing you from removing it. You might use a tool like vice-grips, and apply more force. I don't think you can hurt anything by doing that if the blade is in the fully-extended position.
Good luck,
genetuck
Read full answer
Feb 13, 2011 • Dewalt 15 6" Reciprocating Sawzall Saw...
0helpful
1answer

I have a DW938 and I cannot get the blade to lock into place seems like there is no lock at all.
Hi, If you look at the end where the blade goes in, on the right hand side (as holding it for use in your hands) you should see a yellow lever. First take out the battery, each and every time you change the blade. Lift up the lever, wear some gloves to protect your hand and pull the plade straight out. Push in the new blade with the teeth pointing down, and push the yellow lever down. You can replace the battery once you have completed the above. Hope that was of help to you.
Read full answer
Jan 13, 2011 • Dewalt Dw938 18v Reciprocating Saw Sawzall...
1helpful
1answer

Need to remove and then replace blade clamp on DW305 Type 1. how do you remove the blade clamp? I see two pins
Hello Hollister, on this peticular sawzall they are using a roll pin to hold the blade holder on. If you remove the blade clamp screw, you can move the blade holder back and forth on it. You will need to get a very small punch and drive it all the way out. Look at the picture below. You will need to remove (38) and (52). It will make it much easier.

ptrepair_23.jpg
I hope this helps. If you run into trouble, I'll walk you through it, just post back.
Read full answer
Dec 06, 2010 • Dewalt Saws
1helpful
1answer

Blade not releasing
Hi,
Getting a broken blade our of the sawzall chuck can be difficult and require some ingenuity and patience...
Sometimes there be enough blade left so that you can grab it with a needle nose pliers... othertimes it is flush and that makes it more difficult... holding the chuck in the release position and rapping the saw against a table or with a hammer can jiggle the piece out....of course you have the chuck pointed down while you do that...
Also moving the piece around a bit with a stiff wire and also soaking the chuck and blade with WD-40 helps also....
Usually it will take a combination of these things and some persistance to get the job done...

heatman101
Read full answer
Jul 05, 2010 • Dewalt DC385B 18v. Cordless Bare...
0helpful
1answer

Can not replace blade on Dewalt 303 6.5amp
Hi,
Getting a broken blade our of the sawzall chuck can be difficult and require some ingenuity and patience...
Sometimes there be enough blade left so that you can grab it with a needle nose pliers... othertimes it is flush and that makes it more difficult... holding the chuck in the release position and rapping the saw against a table or with a hammer can jiggle the piece out....of course you have the chuck pointed down while you do that...
Also moving the piece around a bit with a stiff wire and also soaking the chuck and blade with WD-40 helps also....
Usually it will take a combination of these things and some persistance to get the job done...

heatman101
Read full answer
May 23, 2010 • Dewalt DW303 Heavy Duty 65 Amp...
Not finding what you are looking for?

View Most Popular

Dw938 18v Reciprocating Saw Sawzall Recip 18 Xrp

  • Saws

Related Question

A piece of a broken blade is stuck here the blade fits into the saw (Dewalt DW 303m). How do I get it out?

  • Dewalt Saws

107 views

Ask a Question

Usually answered in minutes!

Popular Questions

Dewalt jigsaw (dw321) how to

Dewalt Saws

Change blade on Dewalt DC385 XRP reciprocating saw

Dewalt DC385B 18v. Cordless Bare...

Dewalt table saw stopped working

Dewalt Saws

HOW DO i UNLOCK MY MITER SAW TO LIFT THE BLADE AND

Dewalt DW715 Heavy Duty 12" Single...

My DW 705 compound miter

Dewalt DW703 10" Compound Miter Saw

Top Dewalt Saws Experts

Cindy Wells

Level 3 Expert

6688 Answers

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Sean Wright
Sean Wright

Level 3 Expert

2045 Answers

Are you a Dewalt Saw Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...