Question about Toshiba 50HX70 50" Rear Projection Television

1 Answer

Toshiba 50HX70 convergence problem

I have seen a few articles on this subject but I was hoping someone can give me specific help with this problem. I try to fix the convergence on mt Toshiba color stream (cinema series HD) model 50HX70, but I cannot set it up properly on the left side of the screen. The central crosshair, and all crosshairs on the right and middle of the screen are OK but when I try to fix the cross hairs on the left side, I cannot move the red color (I am missing about a half inch). I am including a picture to demonstrate this. Can anyone recommend a solution?

Posted by on

  • 2 more comments 
  • Patrick Blondin May 12, 2007

    Here is the picture of this problem.

  • centaur Nov 15, 2007

    I have the same problem can't get the red to go all the way over on the cross-hairs

  • kathy4larry Jan 09, 2008

    my problem is my arrow signs don't work to move the red and green colors in convergence screen.



    any help would be appreciated



    Thx

  • krw35 Jan 14, 2009

    Did any of the above posts try this and if so did it work? I have the same problem and am debating whether to order the parts and try to fix it myself (I am not so handy) or just buy a new tv.

×

Ad

1 Answer

Replace convergence ic,s part # stk392-110, you will need two of them.

Posted on May 13, 2007

Ad

1 Suggested Answer

Anonymous

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What is the best small jump start system that you have used ?


Solar jumper packs are what the pros use. No. Solar is a brand of jumper packs made by Clore Manufacturing

Oct 07, 2018 | Cars & Trucks

1 Answer

My camera displays zoom error, the zoom would not retract aand I can't take any shot. From the previous questions and solutions, someone said that taking out the our lens and pushing the inner one till it...


Your camera has a lens error, this is such a common fault that I hope you don't mind me pasting my stock generic answer below. No point in reinventing the wheel! Note that you cannot remove your "outer lens". The lens on your camera is an integrated complete unit and is not designed to be dismantled. Even Fuji service centres will only replace the whole lens assembly and will not attempt to replace just a part of it.

Stuck lenses are probably the most common reason that compact digital cameras get thrown away, but there's a fair chance of recovering use of your camera again

The fault is commonly caused by dirt or grit blocking the mechanism, or due to it having suffered a recent fall. Another common cause is that the camera was in a pocket or bag and the power button accidentally activated and tried to open the lens against resistance. The mechanism may have simply become dislodged or there may be parts which have broken.

If your camera is still under warranty and has definitely not been subject to misuse then contact the Fuji service department in your country to find out about a free repair. If the warranty has expired though a professional repair will far exceed the cost of replacing your camera. You will therefore have nothing to lose by trying to fix this yourself.

Please click here and you will be taken to an excellent article provided by the Camera Repair website. For the most part, you'll be guided on how to physically manipulate your camera to try and clear the fault. Although the article mentions Canon a few times, the advice applies equally to all cameras with lens errors and is not model-specific.

If the link doesn't work then cut and paste the following address into your browser:-

http://camerarepair.blogspot.com/2007/12/fixing-lens-error-on-digital-camera.html

Good luck, I hope you manage to use this information to fix your camera. Please take a moment to rate the free answer I have provided for you and any testimonial which you might wish to add is always welcome!

Oct 05, 2010 | Fuji FinePix S1000FD Digital Camera

1 Answer

My picture goes 3-d like on the sides, and if your looking at the front of the tv inside to the right in the back i notice if I tap it it fixes it temporarily. Can someone walk me thru fixing it please


WS-55819 uses two of the STK-392-570 convergence chips-----usually it is not a soldering problem--I have seen dozens of these sets that use this chip--some of the chips before they totally fail do this--convergence comes and goes--I have also seen several when I unsoldered them that the pins literally fell out of the chips--

I HAVE START TO FINISH, STEP BY STEP INSTRUCTIONS FOR THIS REPAIR IN THIS SET--if you can solder well and are handy--you can buy a pair of the chips on Ebay for less than 13 dollars plus shipping.

I cannot give you my email address but..........

I have also photos of a few things you need to look at if you do this repair----The instructions tell you how to do the repair and also tell you EVERYTHING you will need to do it.

If you have some idea of how I can get the instructions to you other than here let me know--

Take my word for it---if convergence is jumping in or out you need to replace both chips and the set will not have this problem again for 5-8 years--lifespan on these parts.


IF THIS information has helped you, rate this solution as I do this here for free.

SD TECH

Nov 07, 2009 | Mitsubishi WS-55819 55" Rear Projection...

1 Answer

Convergence issues


The full downloadable service manual located Here! will have a list of all parts.
Below are a few remedies for convergence:

Subject

Poor convergence, IC8002

Symptoms / Customer Description
Customer hear a popping noise.
[Primary Symptom Code: 1436 ]

Solution

Found IC8002, IC8003, and fuse PS8006 defective on the D Board.

If you need repair assistance, go HERE!

Nov 05, 2008 | Sony KP-46WT510 46" Rear Projection HDTV

1 Answer

Mitsubishi Convergence Problem


you need to replace the convergence board but it will cost you around $200 to fix the board and components associated with it .......
Have you tried adjusting the convergence settings ........

Oct 13, 2008 | Mitsubishi VS-50605 50" Rear Projection...

2 Answers

Hitachi 51SWX20B Convergence problem


Solution:

Your TV has a convergence problem. Here are some of the most common symptoms.

Screen looks 3D
One or more colors can't be adjusted when using the convergence menu.
Screen is bowed in or warped.

Here is a quick test....

Using your original remote go-to the tv settings then goto the convergence or magic focus section.

Try to adjust the convergence.

You should be able to move them up, down, left, and right.

If you can't move them in all directions your convergence chips are bad and should be replaced. This is a common problem.

Its a fairly easy fix on the Hitachi sets.

You can get a repair kit that includes all the parts from www.TvRepairKits.com. The kit includes a photo instruction guide, original Sanyo STK chips, convergence resistors, etc.
Everything you need to fix it yourself.

Jan 28, 2008 | Hitachi 51SWX20B 51" Rear Projection...

2 Answers

Red and Green Spots


Not a fix for do-it-yourselfers, but check with Panasonic as there is a new fix. Requires tech to come and reprogram the eprom (I think).
Cheaper than a new optic board.

Jan 03, 2008 | Panasonic PT-61LCX65 61" Rear Projection...

1 Answer

What is AF on my camera?


A bit more detail would be helpful to diagnose your specific problem: what mode is the camera in, does it do it all the time or only in certain situations.

There are a few situations when the autofocus does not do well: focus too close to the subject, or in a very low light situation, or the subject is gray. Check that you are not affected by any of these.

Otherwise, try to find if there is something wrong with your camera: find someone else with the same camera (or one in a store display), and see if following the same steps gives you the same result.

Dec 27, 2007 | Cameras

1 Answer

JVC AV-56WP74 closes up and flickers when input is trying to come through


First possibility is a CRT coolant leak onto the signal PCB.
Examine from front and back with good light = even a few drops
of conductive coolant can cause various unusual symptoms....
Your symptoms are multiple and normally un-related, unless,
as you mentioned,all the signals converge......................T.

Nov 22, 2007 | JVC AV-56WP74 56" Rear Projection...

1 Answer

Tv turns itself on and off


Convergence amp ic bad
http://home.earthlink.net/~oleg.filippov/ConvergenceFix.htm
http://cmpalmer.blogspot.com/2006/11/fixing-my-own-tv-part-ii.html
Sony Convergence
http://www.techlore.com/blog/entry/19694/Sony-Convergence-Repair-My-Sony-TV-has-a-distorted-picture-/
http://www.techlore.com/article/19631/Sony-Convergence-Procedure/

Nov 10, 2006 | Hitachi 51SWX20B 51" Rear Projection...

Not finding what you are looking for?
Toshiba 50HX70 50" Rear Projection Television Logo

Related Topics:

482 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toshiba Televison & Video Experts

The Knight
The Knight

Level 3 Expert

76237 Answers

matt martin
matt martin

Level 3 Expert

1257 Answers

Cindy Wells

Level 3 Expert

6073 Answers

Are you a Toshiba Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...