Question about Washing Machines

1 Answer

Maytag dryer model LSG1000 won't shut off even when I open door. Dry cycle ends, control panel lights and heat shut off, but dryer continues spinning. Only way it will stop is if I flip circuit br

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 198 Answers

What happens when power comes back on

Posted on Dec 02, 2012

Ad

6 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Tony Pike

  • 118 Answers

SOURCE: I have a Bosch Maxx

this is because the water can't evacuate . check the pump trap filter and make sure there are no blockages. you will probably find water still i the machine when this happens. There might be a blockage up in the hose pipe before the pump. Good luck

Posted on Jan 22, 2011

Anonymous

  • 1 Answer

SOURCE: Whirlpool Front Load Duet Dryer

Holding the End Cycle button for a few seconds worked! Yes

Posted on Jan 07, 2010

mumma_1

Debs

  • 903 Answers

SOURCE: Door Lock Light - flashing

does the door still lock? becasue it sounds like a faulty lock. It may need to be replaced.

Posted on Oct 23, 2008

Anonymous

  • 27 Answers

SOURCE: Maytag Neptune MAH5500B stopped suddenly - no power or lights

Control Panel is bad, need to replace

Posted on Jun 14, 2009

markfreedman

Mark Freedman

  • 312 Answers

SOURCE: Washer stops in mid-cycle, with a tank full of

Hi,
I don't have the best news for your here. This type of problem is caused by the timer, i.e. main control that you use to select cycles starting to fail.

To start (if you haven't done this already) Pull out the timer knob and rotate it to spin and push it back in. If the spin cycle alone works, it will drain out the machine. If not there is the bail out technique for removing water.
If I am correct, when you put the machine into a normal cycle, the knob rotates, but the machine is silent. Just sits there. The older Maytags are a cut above many other machines on the market.
If you install the timer yourself, you will probably pay about $100.00 for the part.
If you supply me with the model number and serial number, I can give your some instruction on how to do it. They will be located on a placard probably on the top rear of the machine. If my memory serves me correctly
It is not a difficult job. does not require any expensive tools to do. If you do it make sure that the machine is UNPLUGGED FROM THE ELECTRICAL POWER WHILE CHANGING OUT THE TIMER.
Hope this helps,
Have a Happy New Year,
Mark

Posted on Jan 04, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why won't the buzzer alarm go off at the end of a drying cycle


Search Results

    Why does my Kenmore dryer model 417.94802/94862 end ...

    www.shopyourway.com > Manage My Life > Questions
    Why does my Kenmore dryer model 417.94802/94862 end of cycle alarm go off ...washer/dryer unit I do see that it is normal for the end of cycle buzzer to go off ...Why won't my Kenmore dryer model 110.86872100 shut off at the end of the ...

    Why won't the buzzer shut off on my Kenmore 80 Series ...

    www.shopyourway.com > Manage My Life > Questions
    The buzzer won't stop buzzing after the load is complete. ... or turn on the timer and the dryer will start just by selecting a cycle and closing the door. ... The dryer should continue to run and at the end the buzzer should only stay on as long as ...

    FIXED The Buzzer At The End Of The Dryer Cycle Comes On But Won't ...

    www.applianceblog.com/.../21739-The-Buzzer-At-The-End-Of-The-Dry...

    Dec 11, 2010 - 10 posts - ‎2 authors
    My maytag dryer has operated wonderfully until today. All of a sudden the buzzer that goes on at the end of the drying will go on but will not shut off unless I open the door.... To test it: by-pass the push-to-start switch and see if when you turn the timer on and close the door, the ... VERY annoying dryer End of Cycle Signal
    9 posts
    Jun 29, 2012
    Maytag DE8410 electric dryer - End of cycle buzzer stuck ...
    4 posts
    Mar 27, 2011
    Kenmore 80 series, buzzer won't shut off
    2 posts
    Sep 10, 2005
    More results from www.applianceblog.com

Feb 08, 2016 | Whirlpool Dryers

1 Answer

How to fix Maytag dryer MED9600SQ0


Check the thermal cut off, the cycling and the hi limit thermostats.
For continuity or OHMS. If no ohms or resistance they need replacement.

In some dryer's the control panel relies on a thermistor rather than a CYCLING thermostat to regulate the drum's air temperature by monitoring the component's resistance changes; resistance goes down as temperature increases and up when temperature decreases. Once the drum's air temperature reaches a certain level required to dry clothes, the control panel shuts off the heater. The panel will turn the heater on again and begin another heating cycle when the thermistor indicates that more heat is needed to keep the air temperature constant inside the drum 9 this is why in some cases the dryer will operate at lower cycles like gentle or low heat but not at higher settings?)

Lastly check your moister sensor. ( located inside the dryer door usually) Especially if machine seems to shut down early and clothes are still wet.
Test with a meter at room temperature and it should show continuity.
A failed moisture sensor will affect the dryer run time in the automatic moisture sensing cycle but it will not affect the heating of the dryer or the timed cycle. Which are reflected by the thermostats.

Read more :http://www.ehow.com/info_12203962_check-dryer-thermistor.htmlGOD IS So GOOD !!!! AND THAT'S WHY MY ADVICE IS FREE

fix-maytag-dryer-med9600sq0-hdpcwx0uwo4iizhnlkec22xy-5-0.jpg

fix-maytag-dryer-med9600sq0-hdpcwx0uwo4iizhnlkec22xy-5-2.jpg

fix-maytag-dryer-med9600sq0-hdpcwx0uwo4iizhnlkec22xy-5-5.jpg

Jan 26, 2016 | Maytag Dryers

1 Answer

Will broken moisture sensor cause dryer not to heat


In some dryer's the control panel relies on a thermistor rather than a CYCLING thermostat to regulate the drum's air temperature by monitoring the component's resistance changes; resistance goes down as temperature increases and up when temperature decreases. Once the drum's air temperature reaches a certain level required to dry clothes, the control panel shuts off the heater. The panel will turn the heater on again and begin another heating cycle when the thermistor indicates that more heat is needed to keep the air temperature constant inside the drum

Lastly check your moister sensor. ( located inside the dryer door usually) Especially if machine seems to shut down early and clothes are still wet.
Test with a meter at room temperature and it should show continuity.
A failed moisture sensor will affect the dryer run time in the automatic moisture sensing cycle but it will not affect the heating of the dryer or the timed cycle. Which are reflected by the thermostats.

Read more :http://www.ehow.com/info_12203962_check-dryer-thermistor.htmlGOD IS So GOOD !!!! AND THAT'S WHY MY ADVICE IS FREE

Aug 18, 2014 | Maytag Dryers

1 Answer

My 1988 washer/dryer combo Model LSG1000 is showing an E2 code for the dryer. Do you know what that means?


sounds like she might be stuck in an econemy mode ,if its digital try to find its reset button,sometimes very small and out of the way,might have to look up the manual on the net to find this tiny button ,good luck

Feb 12, 2013 | Maytag Dryers

1 Answer

Dryer won't start


First, with the door opened, push and release the door switch. Does the light go on and off?

Dec 07, 2012 | GE GTDL200EMWW 27" Front-Load Electric...

1 Answer

Dryer only shuts off when door is open


test the push button for open and faulty .However see this causes too.

Clogged Vent
If your dryer seems to run forever, it could be because of a clogged vent or internal ductwork. Your dryer may have an automatic cycle that turns off the dryer when the clothes are dry. It does this with a special thermostat or moisture-sensing system.

Normally, this is what happens during an automatic cycle:

The thermostat tells the dryer to heat until the interior of the dryer reaches a pre-set temperature--say 135 degrees.

When the dryer reaches the pre-set temperature, the thermostat tells the timer to begin advancing. (If there's a moisture sensor, the timer advances only if the moisture content of the clothing is low enough.)

The timer advances until the interior cools, then the thermostat tells the timer to stop advancing, and tells the dryer to start heating again.

This cycle continues until the clothes are dry. But...if the vent is clogged, the dryer may never reach the proper operating temperature, so it doesn't send the signal to the timer and the dryer continues to run indefinitely, even if the clothes are completely dry. To fix the problem, clean the vent and/or internal ductwork.


Heating Element

Your dryer's heating element may be partially burned out. If it is, your dryer still heats, but at such a low temperature that it takes three or four times as long to dry the clothes. If the element is partially burned out, replace the heating element. You can check for an ohm reading but will need to refer to the service manual for proper reading. This sometimes on the tech sheet located somewhere on the dryer. Usually between 9-13 ohms.


Cycling thermostat

Although this isn't a common problem, one of the thermostats that controls the temperature in your dryer may break and cause the dryer to heat poorly. If so, you need to replace it. The thermostat is usually a small, round, black device mounted to an oblong steel plate. The plate is mounted to the internal ductwork . This thermostat usually has four wires going to it. Check the 2 terminals that are opposite each other and are the closer together of the 2. These 2 terminals should have continuity. If not replace the thermostat.

Sep 27, 2012 | Frigidaire Dryers

1 Answer

My Maytag gas dryer is not heating correctly. It gets warm, but takes several cycles to dry even small loads.


one thing u can do remove vent tub,
turn on dryer run for about two min
open door touch inside door if hot
u have a vent problem

May 12, 2009 | Maytag PYG2300A Gas Dryer

1 Answer

Maytag atlantis dryer model # mde6400ayw


sounds like the timer is not completing the cycle in this mode will the dryer shut off if you manuelly advance timer in that mode

Oct 21, 2008 | Maytag Atlantis MDE7400AY Electric Dryer

Not finding what you are looking for?
Washing Machines Logo

Related Topics:

253 people viewed this question

Ask a Question

Usually answered in minutes!

Top Washing Machines Experts

Gerry Harvey
Gerry Harvey

Level 3 Expert

1481 Answers

Marvin
Marvin

Level 3 Expert

85206 Answers

Brad Brown

Level 3 Expert

18110 Answers

Are you a Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...