Dryer error what is error e9e

Question 1

0helpful

1answer

I have samsung dryer 8 litres it shows E9 CODE

The only Samsung dryer code that is similar to E9 is 9E1 or E9E. On the SmartCare dryes (gas or electric), 9E1 a power or control board fault. You can try to reset it by unplugging the dryer for 5 minutes (unplug or trip the circuit breaker). If the error recurs, make sure that the incoming voltage supply is between 105 and 130 VAC. If the voltage is correct, then replace the control board. E9E indicates the same problem on other Samsung dryers.

There are some Samsung dryers that may share parts with the Maytag/Whirlpool lines. On these, the E9 error is a door switch failure. Check the latch and hinges. Next check that the switch has the correct resistance across it. Check the wiring, including all contacts and the wiring harness. Replace the control board if the rest of the system is fine.

Please add a comment with your model number for more information.

I hope this helps.

Cindy Wells

Nov 04, 2018 • Samsung Dryers

0answers

Frigidaire dryer. What do the error codes e56 and e9e mean?

Be the first to answer May 19, 2015 • Dryers

0helpful

1answer

Model glgq2152es error code E9E

The E9E code is a low voltage/intermittent voltage alert. It says in the troubleshooting manual to press cancel when this appears.

You may want to check the plug or the wall socket to make sure there is not a short occuring. The fault code is not saying your dryer is broken, just to check for proper voltage.

Jan 10, 2010 • Washing Machines

0helpful

1answer

What is error E9E ans E4A?

this is a line voltage error. press the cancel button for three seconds un plug the unit and have the main power plug checked for the proper voltage and insure that your wires are correct on your dryer

Oct 06, 2009 • Dryers

1helpful

1answer

I keep getting a E9E error code on my Fridgidaire gas dryer. It starts, then stops and flashes the code

this is a line voltage error code press the cancel button for three seconds check you power and make sure the power supplied is correct.

Sep 12, 2009 • Frigidaire Dryers

2helpful

1answer

Dryer front load model # GLG22152ESO, Flashes Error Code E9E

Ok, i would also pull the blower assembly and, check it for clog's as well. clean out the entire exhaust hose as well. if this doesn't stop the shut down, you will need to replace the hi limit thermostat and (dryness)sensor(if equipped) as well.

Jun 09, 2009 • Frigidaire Dryers

2helpful

1answer

KENMORE MOD. 417.84092....RUNS FOR A MINUTE ORTWO OR FIVE / STOPS. HEATS UP OK BUT WON'T RUN FOR MORE THAN A FEW MINUTES. ERROR CODE E9E.

The error code E9E indicates that low voltage is being detected at the control board of the dryer.

This could be caused by the following factors:

* The electrical power supply to the dryer is bad. Check the dryer outlet for proper voltage (120 volts AC).

* Unplug the dryer and check the wiring of the dryer outlet plug. A loose wire on the terminal block could cause this problem.

* If you are able to safely access the control board in the console, check the red wire that connects to the heater relay on the board.

(NOTE: The dryer should always be unplugged when accessing internal components.)
A loose wire or burned connection in this area could result in this error code.

* A failed control board could cause this problem.

Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question

Jun 05, 2009 • Kenmore 62602 Electric Dryer

0helpful

1answer

Kenmore 94082 gas dryer: Runs a short time, then stops, E9E error

The error code E9E indicates that low voltage is being detected at the control board of the dryer.

This could be caused by the following factors:

* The electrical power supply to the dryer is bad. Check the dryer outlet for proper voltage (120 volts AC).

* Unplug the dryer and check the wiring of the dryer outlet plug. A loose wire on the terminal block could cause this problem.

* If you are able to safely access the control board in the console, check the red wire that connects to the heater relay on the board.

(NOTE: The dryer should always be unplugged when accessing internal components.)
A loose wire or burned connection in this area could result in this error code.

* A failed control board could cause this problem.

Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question

Apr 25, 2009 • Kenmore 67082 Electric Dryer

1helpful

1answer

My affinity frigidaire dryer keeps flashing an E9E error code

The error code E9E indicates that low voltage is being detected at the control board of the dryer.

This could be caused by the following factors:

* The electrical power supply to the dryer is bad. Check the dryer outlet for proper voltage (120 volts AC).

* Unplug the dryer and check the wiring of the dryer outlet plug. A loose wire on the terminal block could cause this problem.

* If you are able to safely access the control board in the console, check the red wire that connects to the heater relay on the board.

(NOTE: The dryer should always be unplugged when accessing internal components.)
A loose wire or burned connection in this area could result in this error code.

* A failed control board could cause this problem.

Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question^%$#

Nov 26, 2008 • Frigidaire Affinity 5.8 Cu. Ft. Gas Dryer

6helpful

1answer

I get an E9E fault code on my two year old Frigidaire front loading dryer.

The error code E9E indicates that low voltage is being detected at the control board of the dryer.

This could be caused by the following factors:

* The electrical power supply to the dryer is bad. Check the dryer outlet for proper voltage (120 volts AC).

* Unplug the dryer and check the wiring of the dryer outlet plug. A loose wire on the terminal block could cause this problem.

* If you are able to safely access the control board in the console, check the red wire that connects to the heater relay on the board.

(NOTE: The dryer should always be unplugged when accessing internal components.)
A loose wire or burned connection in this area could result in this error code.

* A failed control board could cause this problem.

Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question

Sep 08, 2008 • Frigidaire Dryers

Question 2

john gagnon

Master 943 Answers
Posted on Jan 11, 2009

john gagnon

Master

Joined: Sep 11, 2008

Answers

943

Questions

1

Helped

324005

Points

2163

Hi The codeE9E means theres a problem with the voltage going to the motor. this is a complicated one I would call a tech to look at the dryer, thanks

Answer 2 · 9/27/2010 12:00:00 AM

Anonymous

15935 Answers
Posted on Sep 27, 2010

SOURCE: my affinity frigidaire dryer keeps flashing an E9E error code

The error code E9E indicates that low voltage is being detected at the control board of the dryer.

This could be caused by the following factors:

* The electrical power supply to the dryer is bad. Check the dryer outlet for proper voltage (120 volts AC).

* Unplug the dryer and check the wiring of the dryer outlet plug. A loose wire on the terminal block could cause this problem.

* If you are able to safely access the control board in the console, check the red wire that connects to the heater relay on the board.

(NOTE: The dryer should always be unplugged when accessing internal components.)
A loose wire or burned connection in this area could result in this error code.

* A failed control board could cause this problem.

Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question^%$#

Anonymous

6784 Answers
Posted on Jun 09, 2009

SOURCE: Dryer front load model # GLG22152ESO, Flashes Error Code E9E

Ok, i would also pull the blower assembly and, check it for clog's as well. clean out the entire exhaust hose as well. if this doesn't stop the shut down, you will need to replace the hi limit thermostat and (dryness)sensor(if equipped) as well.

Anonymous

15935 Answers
Posted on Sep 27, 2010

SOURCE: Kenmore 94082 gas dryer: Runs a short time, then stops, E9E error

The error code E9E indicates that low voltage is being detected at the control board of the dryer.

This could be caused by the following factors:

* The electrical power supply to the dryer is bad. Check the dryer outlet for proper voltage (120 volts AC).

* Unplug the dryer and check the wiring of the dryer outlet plug. A loose wire on the terminal block could cause this problem.

* If you are able to safely access the control board in the console, check the red wire that connects to the heater relay on the board.

(NOTE: The dryer should always be unplugged when accessing internal components.)
A loose wire or burned connection in this area could result in this error code.

* A failed control board could cause this problem.

Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question

Answer 3 · 9/27/2010 12:00:00 AM

Anonymous

15935 Answers
Posted on Sep 27, 2010

SOURCE: my affinity frigidaire dryer keeps flashing an E9E error code

The error code E9E indicates that low voltage is being detected at the control board of the dryer.

This could be caused by the following factors:

* The electrical power supply to the dryer is bad. Check the dryer outlet for proper voltage (120 volts AC).

* Unplug the dryer and check the wiring of the dryer outlet plug. A loose wire on the terminal block could cause this problem.

* If you are able to safely access the control board in the console, check the red wire that connects to the heater relay on the board.

(NOTE: The dryer should always be unplugged when accessing internal components.)
A loose wire or burned connection in this area could result in this error code.

* A failed control board could cause this problem.

Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question^%$#

Answer 4 · 6/9/2009 12:00:00 AM

Anonymous

6784 Answers
Posted on Jun 09, 2009

SOURCE: Dryer front load model # GLG22152ESO, Flashes Error Code E9E

Ok, i would also pull the blower assembly and, check it for clog's as well. clean out the entire exhaust hose as well. if this doesn't stop the shut down, you will need to replace the hi limit thermostat and (dryness)sensor(if equipped) as well.

Answer 5 · 9/27/2010 12:00:00 AM

Anonymous

15935 Answers
Posted on Sep 27, 2010

SOURCE: Kenmore 94082 gas dryer: Runs a short time, then stops, E9E error

The error code E9E indicates that low voltage is being detected at the control board of the dryer.

This could be caused by the following factors:

* The electrical power supply to the dryer is bad. Check the dryer outlet for proper voltage (120 volts AC).

* Unplug the dryer and check the wiring of the dryer outlet plug. A loose wire on the terminal block could cause this problem.

* If you are able to safely access the control board in the console, check the red wire that connects to the heater relay on the board.

(NOTE: The dryer should always be unplugged when accessing internal components.)
A loose wire or burned connection in this area could result in this error code.

* A failed control board could cause this problem.

Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question

Related Topics:

Trustworthy Expert Solutions

Dryer error what is error e9e

1 Answer

john gagnon

3 Related Answers

Anonymous

Anonymous

Anonymous

Add Your Answer

Attachments: Added items

Related Questions:

I have samsung dryer 8 litres it shows E9 CODE

Frigidaire dryer. What do the error codes e56 and e9e mean?

Model glgq2152es error code E9E

What is error E9E ans E4A?

I keep getting a E9E error code on my Fridgidaire gas dryer. It starts, then stops and flashes the code

Dryer front load model # GLG22152ESO, Flashes Error Code E9E

KENMORE MOD. 417.84092....RUNS FOR A MINUTE ORTWO OR FIVE / STOPS. HEATS UP OK BUT WON'T RUN FOR MORE THAN A FEW MINUTES. ERROR CODE E9E.

Kenmore 94082 gas dryer: Runs a short time, then stops, E9E error

My affinity frigidaire dryer keeps flashing an E9E error code

I get an E9E fault code on my two year old Frigidaire front loading dryer.

Not finding what you are looking for?

GLEQ2152ES Electric Dryer

I have samsung dryer 8 litres it shows E9 CODE

Ask a Question

Top Frigidaire Dryers Experts

Brad Brown

ZJ Limited

Paul Bade

Are you a Frigidaire Dryer Expert? Answer questions, earn points and help others

Manuals & User Guides

. GLEQ2152ES Electric Dryer Manual

Related Topics:

Trustworthy Expert Solutions

Dryer error what is error e9e

1 Answer

john gagnon

3 Related Answers

Anonymous

Anonymous

Anonymous

Add Your Answer

Attachments: Added items

Related Questions:

I have samsung dryer 8 litres it shows E9 CODE

Frigidaire dryer. What do the error codes e56 and e9e mean?

Model glgq2152es error code E9E

What is error E9E ans E4A?

I keep getting a E9E error code on my Fridgidaire gas dryer. It starts, then stops and flashes the code

Dryer front load model # GLG22152ESO, Flashes Error Code E9E

KENMORE MOD. 417.84092....RUNS FOR A MINUTE ORTWO OR FIVE / STOPS. HEATS UP OK BUT WON'T RUN FOR MORE THAN A FEW MINUTES. ERROR CODE E9E.

Kenmore 94082 gas dryer: Runs a short time, then stops, E9E error

My affinity frigidaire dryer keeps flashing an E9E error code

I get an E9E fault code on my two year old Frigidaire front loading dryer.

Not finding what you are looking for?

GLEQ2152ES Electric Dryer

I have samsung dryer 8 litres it shows E9 CODE

Related Topics

Ask a Question

Popular Questions

Kenmore Oasis dryer F40 error code

Error code on a Frigidaire affinity dryer E64

Error Code E68 on frigidaire affinity dryer.

What does error code E65 mean on dryer.. does not dry clothes well

My frigidaire affinity dryer displays LOC

Top Frigidaire Dryers Experts

Brad Brown

ZJ Limited

Paul Bade

Are you a Frigidaire Dryer Expert? Answer questions, earn points and help others

Manuals & User Guides

. GLEQ2152ES Electric Dryer Manual