I have got 4 voltek cameras which have worked perfectly until one stopped recording except at close range. i swopped 2 of the cameras around to see if the other camera would pick up. i switched off at the dvr but not at the mains, when i switched on again it would not record properly, so reset the unit but i cannot set it up to record on motion detect, it will record on manual only
many thnks for the help but i did manage get it fixed myself after reseting it again and carefully going through all the set up processes
thanks againmany thnks for the help but i did manage get it fixed myself after reseting it again and carefully going through all the set up processes
thanks again
You can't post conmments that contain an email address.
Press the “Menu” button and use the Up or Downbutton until “Motion” is highlighted then press the “Enter” button. Use the Up or Down button to highlight the “OFF” next to “MOTION RECORD” and press the + or -button until “ON” is shown. Use theUp or Down button to Highlight the (MENU) then camera you wish to enable, then use the Left or Right button to highlight the “OFF” next to that camera and press the + and - keys to adjust the setting to “ON”. Use the Right key to highlight “AREA” next to the camera you wish to enable, and press the “Enter” button. Press the - button to turn on Motion Detection for the whole screen as shown by a green overlay, then do the same for your other active cameras.
Hello, I have a Swann Pro 4000 and need to know how I can go online to monitor my home from another city via the Internet. If anyone can help me thank you very much. My internet system is DSL and used one router Linksys.
- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
It may likely be a mismatch in camera and DVR technology. Since the HD over coaxial cable cameras hit the market, there have been many protocols of HD cameras. SDI, TVI, CVI and AHD are the 4 using their technology. Hikvision and Dahua, the 2 largest manufacturers of CCTV now make their DVRs cross compatible with all protocols except SDI which is Korean and was the first. SDI is kind of dying a slow ***** due to the other less costly versions of HD cameras. Their DVRs detect the protocol and make it work automatically. There is also the analog or non-HD which is not compatible with the HD. So if you have different protocols and you are using low grade manufacturers that don't allow cross compatibility, then that is the issue. These lower tier manufacturers like Bunker Hill and Swann don't even tell you the protocol on their spec sheets most likely. This also causes confusion for end users and even techs like me. So my recommendation would be to call the manufacturer and see if they will tell you their dark secret about which protocol they use. They usually won't or the tech support will not even know. My advice is to switch to a better manufacturer.
No its not. You might get it display an image but will probably be black and white as the resolution on the cam is higher than the supported resolution on the dvr
Have you tried a hammer? Kidding!!! Usually this is a conflict in resolution between the DVR and the TV. You may need to lower the resolution of the TV for the particular input you are using. You may have a 1080P TV and a 720P DVR. Once they match, the issue should be resolved.
1) delete the operating prog. from mobile and reinstall and then try to run 2) if it is running on Dynamic IP then check your mobile port is forwarded in Router or Not 3) make new Id on Dyndns then operate
Hard drive failure. Open the case, unplug power wire from hard drive. Power on the system. If everything works except recording, then you have fried hard drive. Replace it, format it, and you are back to normal.
many thnks for the help but i did manage get it fixed myself after reseting it again and carefully going through all the set up processes
thanks again
×