Kenmore 3.2 cu. ft. Plus Top Load Washer Logo
MaryC Posted on Jan 06, 2013
Answered by a Fixya Expert

Trustworthy Expert Solutions

At Fixya.com, our trusted experts are meticulously vetted and possess extensive experience in their respective fields. Backed by a community of knowledgeable professionals, our platform ensures that the solutions provided are thoroughly researched and validated.

View Our Top Experts

Kenmore 90 series washing machine, heavy duty, super capascity plus,quiet pak2 3spd motor w/5spd combo, when in spin mode, it smells like melted crayons

Yesterday morning, we had to replace the grey water drain hose on washing machine, as it had a whole in it.After changing hose, i began to smell, when in spin mode, a strong smell of melted crayons coming from washer. this started last night. I have used washer all day & washer is losings its ability to spin water out of clothes. help

1 Answer

Anonymous

Level 2:

An expert who has achieved level 2 by getting 100 points

All-Star:

An expert that got 10 achievements.

MVP:

An expert that got 5 achievements.

Sergeant:

An expert that has over 500 points.

  • Expert 291 Answers
  • Posted on Jan 07, 2013
Anonymous
Expert
Level 2:

An expert who has achieved level 2 by getting 100 points

All-Star:

An expert that got 10 achievements.

MVP:

An expert that got 5 achievements.

Sergeant:

An expert that has over 500 points.

Joined: Nov 24, 2012
Answers
291
Questions
0
Helped
110414
Points
908

If drain hose is connected to a standpipe check that it's inserted no more than 4". You may be getting a syphoning situation that is allowing gray water to contaminate clean clothes.

4 Related Answers

tzweeb

Tom Zwiebel

  • 318 Answers
  • Posted on Jan 31, 2009

SOURCE: kenmore 90 plus series: heavy duty super capacity won't agitate

this is the site to find out how to fix your washer.
you have a broken drive coupling.
it probably wont agitate or spin, but will fill and drain.
you need to remove 2 screws from the control panel, hinge it back and then remove the 2 brass colored clips that hold the cabinet to the base. once you do then pull the entire cabinet forwards to a 45 degree angle and pull it off the base.
then pull the 2 clips off pump and then 2 more on the motor. that will allow you to get to the drive coupling. you will find it to be broken.
replace it with part number 285753a for about 15-20 bucks.

Ad

Anonymous

  • 3361 Answers
  • Posted on Feb 26, 2009

SOURCE: kenmore 82372110 70 series heavy duty plus won't spin

If it drains and won't spin you have to replace the direct drive coupling.

Anonymous

  • 5911 Answers
  • Posted on Aug 12, 2010

SOURCE: Kenmore 90 series heavy duty super capacity plus

If your TOP LOADING Whirlpool manufactured washer (Kenmore) is leaking, the following link explains how to remove the exterior washer case in order to accurately inspect the washer interior components for the source of your leak:

http://www.fixya.com/support/r3576648-washer_leak__top_loader


If the leak is more like a constant drip, a common source of leaks with Whirlpool manufactured top loaders is a leaking drain pump. These pumps are not serviceable and if damaged, must be replaced. The following link explains how:

http://www.fixya.com/support/r3794382-replacing_water_pump_whirlpool_top


Don't forget to check all drain hose connections under the washer and the center tub seal.

Replacement parts (if required) can be purchased at any of the following websites:

searspartrsdirect.com
pcappliancerepair.com
appliancepartspros.com
repairclinic.com

Prices vary between sites, so shop and compare. The first three sites listed also have helpful exploded view parts illustrations to assist you with locating and properly identifying the parts you may need.

If you have any questions, please post back with a complete MODEL NUMBER and let me know. I hope this helps you.

Anonymous

  • 176 Answers
  • Posted on Sep 15, 2010

SOURCE: Kenmore 90 series Heavy Duty Super Capacity Plus

hi check the lid swetch

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

I have kenmore 80 series heavy duty/ super capacity plus washer that after it fills with water,hot or cold and it starts the wash cycle, I noticed that the agitator only moves once in awhile and stops

hum either a bad timer sticking the point contacts close. have u tried this in all cycles? and possibly a motor with bad windings not enough power to run agitation? try running in mild or gentle and see what happens? I was tempted to say the cam dogs in agitator but they dont work then stop then work, when they go out they go out.
0helpful
1answer

70 Series Kenmore Washer Agitates in Heavy Duty regardless of switch selection

Yours is a 2 speed motor. Does it spin in 2 different speeds. If so, then it most likely is designed with only to agitate in 1 speed. If it only spins in one speed, then your motor is defective
12helpful
2answers

Kenmore 90 Series Heavy Duty Washer - Agitator doesnt spin

THIS IS A TYPICLE PROBLEM . BETWEEN THE MOTOR & THE TRANSMISSION THERE IS A COLLECTOR ASSEMBY (THREE PIECE
SET) REAL EASY TO GET TOO EASY TO FIX . ALSO COST EFFICENT
2helpful
1answer

My washing machine won't spin!

as with basic spin faults -a number of reasons usually 1 motor brushes, 2 motor 3 motor control pcb or the obvious one - the belt has come off.
1helpful
1answer

Kenmore 82372110 70 series heavy duty plus won't spin

If it drains and won't spin you have to replace the direct drive coupling.
1helpful
1answer

Washer works but smells like its burning.kenmore 90 series heavy

The burning smell could be the motor going out. When the water gets into the tub and makes it heavy it puts strain on the motor and the motor may be getting weak.
12helpful
2answers

Kenmore 90 plus series: heavy duty super capacity won't agitate

this is the site to find out how to fix your washer.
you have a broken drive coupling.
it probably wont agitate or spin, but will fill and drain.
you need to remove 2 screws from the control panel, hinge it back and then remove the 2 brass colored clips that hold the cabinet to the base. once you do then pull the entire cabinet forwards to a 45 degree angle and pull it off the base.
then pull the 2 clips off pump and then 2 more on the motor. that will allow you to get to the drive coupling. you will find it to be broken.
replace it with part number 285753a for about 15-20 bucks.

1helpful
1answer

I also need the answer...

Verify Lid switch ..... A solved rating is great motivation to continue giving priceless advise........
Not finding what you are looking for?

219 views

Ask a Question

Usually answered in minutes!

Top Kenmore Washing Machines Experts

Alexander

Level 2 Expert

171 Answers

Cindy Wells

Level 3 Expert

6688 Answers

vince

Level 3 Expert

2530 Answers

Are you a Kenmore Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...