Http://198.162.1.1 cannot get onto above link have tried reboot etc changed all settings as suggested in previous posts at aloose end, pls help !!

Facebook Customer Support:
Phone Number: 1-650-543-4800
Average Wait: 12 minutes - 24 hours, 7 days
http://gethuman.com/phone-number/Facebook/
Facebook Customer Phone Number Shortest Wait Best Support
IF YOU LIVE OUTSIDE THE USA CLICK ON LINK ABOVE AND THEN CLICK
ON CALL FREE VIA WEB.
Suggest trying a new browser like Firefox or Google Chrome
YOU CAN GET THEM INSTALLED AT THE LINK BELOW:
http://www.ninite.com
By the way their are over 27,000 unanswered Facebook questions
that need to be answered. If no one answers them I will attempt
to.

Facebook Customer Support:
Phone Number: 1-650-543-4800
Average Wait: 12 minutes - 24 hours, 7 days
http://gethuman.com/phone-number/Facebook/
Facebook Customer Phone Number Shortest Wait Best Support
IF YOU LIVE OUTSIDE THE USA CLICK ON LINK ABOVE AND THEN CLICK
ON CALL FREE VIA WEB.
Suggest trying a new browser like Firefox or Google Chrome
YOU CAN GET THEM INSTALLED AT THE LINK BELOW:
http://www.ninite.com
By the way their are over 27,000 unanswered Facebook questions
that need to be answered. If no one answers them I will attempt
to.

Check the link http://www-01.ibm.com/support/docview.wss?uid=nas8N1013805

Hope it helps

Hi,
https://cradlepoint.com/support/cradlepoint-mbr1200
links to various pdfs.
https://cradlepoint.com/sites/default/files/mbr1200_datasheet.pdf
https://cradlepoint.com/sites/default/files/mbr1200_manual.pdf
This one seems most likely to help:
https://cradlepoint.com/sites/default/files/mbr1200_qsg.pdf
does show 'http://192.168.0.1' as the browser-access URL.
Questions:
Your browser isn't putting in 'https'?
Tried multiple browsers?
Rebooted your computer ("if in doubt, reboot", esp w Windows...)?

Hmm, only place the 'CP' designation shows up is on the EOL page. Vendor is likely to be no help...
http://knowledgebase.cradlepoint.com/articles/Support/Product-End-of-Life-Policy
end of life on August 25, 2011
end of support: 04/15/2012
last firmware release: version 2.2.1 posted on April 4, 2013.

Helpful?

Click the Link.


Depending on you security setting, you may encounter these steps in this link. Link 2
If the link above does not work try this links below. Link 3 Link 4
Thank you for posting, hope this helps.

Hi,

I would like to know if you are trying to print directly from the Camera print option or have you downloaded the photos from your Camera to the PC and then trying to print ?

If you are trying to print from Camera to PC then there may be a delay time. Instead my suggestion would be to copy/transfer the photos from your Camera SD card to the PC and then print the photos.

Also, If you have not installed the drivers/software of your camera on the PC, click on the link below to download and install the drivers.
Download Link 1

OR
If you are not able to download from the above link, try the below one

http://tinyurl.com/2kz82h

Step 1 - download the file at the link in my previous post. It will be a file called DSC07.exe

Step 2 - Do NOT run this file yet!

Step 3 - if you have plugged in the camera at any point previously, replug it in and then go to Control Panel, System, Harware, Device Manager. Find the device, it may have yellow triangle, red X, or even just be there normally. Once found, right click on it and click 'remove'. You may have to reboot.

Step 4 - Go to control panel - add/remove programs and uninstall any Sipix or StyleCam driver programs you have. (You do not need to uninstall any ArcSoft programs)

Step 5 - definitely reboot at this point

Step 6 - run the downloaded DSC07.exe program to completion

Step 7 - reboot again

Step 8 - plug the camera in and all should be well

Regards,
FixYa


*Please rate this solution with Thumbs Up

IF YOU ARE USING GENERIC CARTRIDGES, MAYBE IT WOULD BE BETTER IF YOU DISABLE THE INK MONITOR.

This is the only advice I can give you.

The next step would be to disassemble the Epson, and clean the Pads/Heads. Click on link below.:
http://www.hm2k.com/posts/parts-inside-your-printer-are-at-the-end-of-their-service-life

I located a page on http://www.fixyourownprinter.com forum, which had plenty of details about similar issues.

If you find this helpful, pls rate me.

Thanks and Good Luck :0)

Find your answer here please.

http://www.fixya.com/support/t599615-hp_photosmart_d7460_problem

this link to a answer previously Posted by a FixYa.com question catcher HarleyHawk

where do i get free apple ipod games????

Hi marijajev, There are two (2) things we can do, but let's give the first one a try first and pls post back the results before I post the second one if that's ok with you. 1. On your laptop, open your browser: 1.1 Internet Explorer - click on Tools/Internet Options/Connections Tab/LAN Settings/Check Automatically detect settings, OK, OK, or 1.2 Mozilla - click on Tools/Options/Advanced/Network Tab/Connection Settings button/Tick Auto-detect proxy settings for this network, OK, OK, or 1.3 Opera - click on Tools/Preferences/Advanced Tab/Proxy servers button/Tick Use automatic proxy configuration, OK, OK It is better to reboot. After rebooting, right click on your networking icon bottom right side in your System Tray and click on repair. If the any of the above works then your set, if not you can always revert back to the original settings but pls post back status that I may post 2nd. Hope this works out for you. Good luck and kind regards.

Hi, On another posting of a similar problem, I proposed this solution: In some instances, the PC switches off a USB port. You may have to un-check "Allow the computer to turn off this device to save power." This is in your Device Manager/Universal Serial Bus Controllers/USB Root Hub. Hope this be of some help/idea. Pls post back how things turn up or should you need further information. Good luck and kind regards.