NO LEARN BUTTON ON GUN VAULT 1000

Lots of info and videos' here, whatever this nonsense means :>D

https://www.google.com/search?q=reset+the+code+to+a+zillionz+secret+code+vault

..

Yes, in case you press and then hold on to the red button found on the side of the opened lid, you will see the lights on top of its lid flashing green which shows that you're in a silent mode.The Gunvault GVB2000 Multi Vault Biometric Gun Safe can store 30 different Multi Vault.

Call a lock smith

To ensure that old codes do not work, first press and hold the SR code button (Learn) on the garage door opener's control panel. Hold the button until the LED goes out. The Learn button is a colored button that is usually on the back panel to the left of the force and up/down adjustment knobs. Sometimes the control panel is on the side of the unit.

Next get a helper to make the programming easier. One person will need to press and release the Learn button. Then within 30 seconds, the second person (or a fast moving individual) needs to type in a 4 digit code and press the enter key on the key pad. The LED near the learn button will flash when the code is received.

If you reset all of the codes, you'll need to repeat the fast press and release of the Learn button. Then press a control button on the remote for most of your other door opener remotes. (There may be a pair of remotes that came with the garage door opener that will never be forgotten.)

I hope this helps.

Cindy Wells
(This works for all of the Craftsman door openers that I've dealt with.)

Hello there,
It actually depends on what you are trying to program. And these instructions apply only to openers that do not have dip switches on them.
Remotes: push don't hold the colored learn code button all models have different colors. After pushing the button hold the remote behind your back and push it three times. On the third time the door should run.
Keyless Entry: Program the code you want into the keyless. Push the colored learn code button and then enter the code and push enter three times slowly. on the third time the door should run.
Home-Link. Hold the two outer buttons until the blinking pattern changes. Then hold the button you wish to program and point and click your remote at it. Push the colored learn code button and push the homelink button three times.
There are two models of the Wireless Keyless Entry System, the 740CB and the 940CB. The 940CB is for use only with Security+® garage door openers having an orange/red smart/learn button. The 740CB will work with all openers manufactured since 1990 that have a yellow, white, gray, or green smart/learn button. It will not work with Security+® openers.
To program the keyless entry, first locate the smart/learn button. On our chain drive models, this button is on the end farthest from the door. On our belt and screw drive models, it is on the right side as you face the door from the opener. You simply press and release the smart/learn button. You now have 30 seconds to enter your four digit PIN number into the keypad and hold the enter button for five seconds. Wait one minute and test the keyless entry by entering your four-digit PIN number and pressing enter.
With some Security+® models, you can also program your Model 940CB Wireless Keyless Entry without climbing a ladder, right from your Multi-Function Control Panel. Simply enter your pre-selected code and press and hold the enter button on your Keyless Entry. Then press and hold the light button and the pushbutton on your Multi-Function Control Panel. The garage door opener lights will flash to confirm that the Keyless Entry has been successfully programmed.
Hope this helped you solve the problem. All the best my dear friend. Elect_Comp

I went here for your manual:

Gunvault Multi Vault GV2000

Do you have the key?

Looks like you can remove power for 30+ seconds and reset to the factory defaults (there's external power and AA batteries inside.)

The PDF file linked above has the "learn" precedure for setting the code. And there's a FAQ list on page 13 that you might find helpful.

Good luck!

:o)

Enter the 1,2,3,4 factory number.
When the door opens, immediately press all 4 keys are once and release.

A red light will come on. then enter new code. lamp will turn off.


to confirm the new code enter it a second time.
red light blinks, an error has occurred or your timing was off, so just start over with the factory 1,2,3,4 code.

That is not a valid IP address.
IP addresses must end with .1 to .254
I am surprised that it let you set it to zero

Best bet is to reset the media vault to factory defaults and then follow the manual to set it up. Go to support.hp.com for more info.

If this helps, please vote for my solution.

If it's a toy, try taking off the hinges, you can always glue it back on later.

Hi, I found something on amazon, take a look: Amazon com gun vault manual Have a nice day