I nees a setup sheet to re-install my P4350

Installing Ashampoo software is a simple process that can be done in a few steps:

1. Download the software: Go to the Ashampoo website and download the software you want to install.
2. Run the setup file: Once the download is complete, double-click on the setup file to begin the installation process.
3. Follow the prompts: The installation wizard will guide you through the process. Click "Next" to continue through the steps.
4. Choose the destination folder: Select the folder where you want to install the software. You can choose the default location or select a different one.
5. Begin the installation: Click "Install" to begin the installation process. It may take a few minutes to complete.
6. Complete the installation: Click "Finish" to complete the installation process.

It is important to note that some of the Ashampoo software may have different installation process, please make sure to read the instructions carefully and follow the steps accordingly. Also, you may need to restart your computer after installing the software to ensure that it runs smoothly.

Make sure that the printer driver is properly installed. Please visit the Lexmark website to download and install the Lexmark P4350 Printer Driver on your computer. Select your operating system > click on "FILTER" > click on the driver under Recommended Downloads > download and execute the file. After the install process is complete, try to print again to verify that the problem is fixed.

There are Lexmark P4350 drivers available for download in the Lexmark website. Just click on this link: http://bit.ly/9yASdX. Click on the Microsoft or Macintosh dropdown found below the page to choose the version of the operating system of your computer. Hope this helps. If you need more assistance, leave a comment and I'll get back to it. Thanks.

Hello. You will need to install the scan software in your computer first. The software can found in the installation cd that came with your printer. Insert the installation cd in your computer and install the software. Just follow the instructions carefully. The software enables the computer to communicate with the printer and vice versa. Without it installed, you won't be able to print/scan from your computer. There is also a link to the Lexmark website where you can download the User Guide. It will give you detailed instructions on how to scan and do other features the printer can do. Just click on this link: http://bit.ly/b6359P . Click on Publications tab found at the center of the page. Download the PDF file User Guide. Hope this helps. Good luck!

try out the website,, it has the drivers and all the other guides,,,,
download and install...
http://support.lexmark.com/index?locale=en&segment=DOWNLOAD&startover=y&userlocale=EN_UK&question=Lexmark+P4350+All-In-One+InkJet+Printer&productCode=LEXMARK_P4350&page=answers&detectedProductFacet=CMS-CATEGORY_REF.LEXMARK.PRODUCTS.ALLINONE.LEXMARK_P4350&searchid=1268337423489#1

Here is the Setup Sheet:

Lexmark 6100 Series Setup

And...the User Guide:

6100 Series User Guide

Here is the link to download drivers if needed:

6100 Support

Click on the Downloads tab. Select the correct one for your Opeating System.

http://www.downloaddelivery.com/downloads/cpd/cjb4300EN.exe

download this driver and install it..

In order for you to setup the WRt54G to work with your Ibook you nee d to manually configure it since the setup CD for the WRt54G wont run on your MAC computer, In manually configuring the router you need to access the setup page of it and there you can set it up, I will advice you to contact Linksys tech support so one of their tech can walk you through with the process the number 800-3267114 they are open 24/7...

Hope that helps...........

Please do not worry, u can download installation software from this link :
http://downloads.lexmark.com/cgi-perl/downloads.cgi?lxkprod=Lexmark+P4350

Hello,

 

My name is Vikram Kumar Thumu, from India-Hyderabad. I have seen your message on the issue related to loading the paper    . I would like to provide my suggestions on the issue. I hope that this should work for you and will resolve the issue.

 

Please try below steps if you want to know how to load paper in to the Feeder.:

Important: When loading paper into the feeder, make sure you are using separated (i.e., cut) sheets of paper. Banner paper that is connected end-to-end should not be used unless you are specifically printing a banner.

To load separated sheets of paper:

1. Obtain a fresh stack of paper.
2. Separate the paper by bending it back and forth in an "S" shape before loading it into the printer.
3. Place the paper against the right side of the sheet feeder, with the print side facing you.
4. Gently insert the paper into the feeder. Do not  force the paper down into the printer.
5. Squeeze the release tab and the paper guide together, and slide the paper guide to the edge of the paper.

Humid conditions may cause some sheets of paper to stick together.

 

If the issue still persists,  then I recommend you to look in to USER MANUAL that is provided along with Printer for instructions on loading Paper.

 

Well, for your convienience I'll provide you with steps that helps to access USER MANUAL.................

 

Steps are :

If the Lexmark P4300 software is already installed in Windows:

1.  Go to Start, (All) Programs, and point to Lexmark P4300 Series. 
2.  Select User's Guide.
   
   
   

If you have not yet installed the Lexmark P4300 software, you can find the User's Guide on the installation CD.  Do the following:

1.  Insert the CD into the CD-ROM drive. The Lexmark installation screen should appear.
   • If the screen does not appear, open My Computer and double-click on the 4300 Series icon.
2.  Click on the ?  icon to the left of View User's Guide (including setup troubleshooting).  You will be asked whether you would prefer to save the User's Guide to the desktop and view it from there (Yes), or to view it from the CD (No). 
3.  Select the option you prefer.

This should resolve the issue for you.

 

 If you need any further assistance on the issue, you can mail me at [email protected] . I'll be glad to help you.

 

Bye.