Could the problem be. Cos it's jumping around and loosening the screw in the centre ?

If you're in the MATHPRINT mode, press
2ND [COS^-1] ( 8 - 3 2ND [sqrt] 2 1 right-arrow ) / 2 5 ENTER

If you're in the CLASSIC mode, press
2ND [COS^-1] ( 8 - 3 2ND [sqrt] 2 1 ) ) / 2 5 ENTER

In either case you should get an answer of about 103.

Hope it's the LCD Display problem if not the pata that connect the board and the LCD (display or screen)
Please try by replacing the (LCD)screen.
Note: If you can't fixed it by yourself then please refer to the nearest mobile service centre. (Cos' the LCD price is high)

Thanks for using FixYa!

By misaligned do you mean the door hits the inside liner of the
freezer? If so then loosen the three screws that secure the top hinge
and reposition the door so it clears the freezer liner, then retighten the screws. If by misaligned you mean the door is warped so that the door
dosn't fit tightly all the way around then you need to loosen all the screws under the door gasket and then twist the door so it seals evenly all the way around the door. (Hint loosen the screws just enough so
the door will stay aligned after you twist it). Good Luck

Insert a flat blade screwdriver under the inside lip of the chrome rim and it will pop out. Then loosen the three screws around the headlamp retainer and move to the left ( might be right ) and the retainer will slide off the loosened screw and allow removal of the headlamp.

Put your bike on a stand so there's no weight on the front wheel. Take the whole cap off the top of your fork, on the underside of the broken screw as centrally as possible centre punch a mark, then using a very small drill gently drill through, increasing the drill size gradually, the drill action and the heat generated may loosen the screw if not a bit of persuasion with an impact screwdriver set clockwise should do the job.

Avensis 2004 (2003-2007 model)
Removed as there was something rolling around inside the steering wheel, causing the horn to randomly activate

Unit has airbag, I didn't fancy the idea of the unit going off so I disconnected the battery as a precaution

Loosen the two "torx" screws on either side of the steering wheel (on sides next to the stereo controls on one side and blank/cellphone controls on the other side) , they will loosen, but not completely come out as they are held in by a plastic "cage".

Use a magnet to 'hold' one of the torx screws out as far as possible, whilst slowly wiggling the centre of the steering wheel out on that side (it won't completely remove), repeat the same on the other side, the centre should now come out (it's a firm fit), but note that the removed piece is still connected via cables (for the airbag), I did not need to remove these to perform my repair, so I am unsure as to what would be required to 'reset' airbag (if anything) once these are disconnected.

The torx screws need to be located in the plastic cages (on the recess on the Torx screw head) to hold them in place whilst refitting the centre of the steering wheel.

all nokia code on www.aliwix.tk

some of the nokia 6300 mobile as the same problem after changing there battery your battery does not fit to your model mobile phones change the battery or make your battery to fit to your mobile then it will be back as good it was.If you have same problem means take out your memory format your memory card.

1. snap the chrome adjuster off
2. start unthreading centre of head. I used a paint scraper to leverage at first. The threads get loose soon to hand loosen.
3. loosen the spray ring using a lever to get threads started. Hand loosen after that.It's got right hand thread so the outer ring will be turning counter clockwise.
4. Take flat rubber gasket out of centre of head and take screw out, then pry white nylon part out with tool. I used tweezer.
5. Clean scraped parts in hot CLR solution or any vinegar will work as well. Reassemble with lubricant so it works like new. Most likely need for disassembly is clogging or a broken "o"-ring.

brake drums ar faily simple to change, if u take the wheels off ul see a little centre cap, behind the cap theres a 21 mm nut, be careful not to mix up the nuts cos they are opposite threads, n/s is left hand thread.
remove the nuts (i advise replacin the nuts) then tap the drum while u spin it jus to loosen it off then jus pull it off, be careful with the bearing cos they'll fall out, IMPORTANT! when tightening the centre nuts back up they jus need to be nipped up NOT tight, jus enough to take the play out of the bearings but keep it spinning freely, when put the wheels back on make sure theres no play in it