A Netgear wireless router attaches multiple devices to your
Internet connection, either by ethernet cable or wirelessly.
If you can't connect to the Internet, the problem can be
anywhere along the chain of devices and technologies that connect your computer
to the Internet.
Knowing how to troubleshoot your Netgear or other wireless
router is an essential part of determining where the problem is and fixing it.
Click your "Start" button, and choose "Run."
Type "cmd" in the text box (without quotation
marks), and click "OK."
A command prompt will open. Type the following: ipconfig
/all. Press your "Enter" key.
A list of numbers and other networking configuration
information will display.
Find your network adapter in this list of headers.
If you use your computer wirelessly in many different
places, you may have to scroll through a lot of different options to find your
adapter.
If you connect to the Internet using a cable, look for a
header that begins with "Ethernet adapter Local Area Connection."
If you connect wirelessly, look for a header that begins
with "Ethernet adapter Wireless Connection."
You will usually only see an IP address displayed under one
header in either category.
Record your IP address and default gateway on a piece of
paper or in a text file.
If your IP address is 0.0.0.0 or begins with 169.254, unplug
your Netgear router from its power source.
Unplug your cable or DSL modem as well.
Be sure to unplug both devices; turning them off with a
power switch may not have the same effect.
Wait 20 seconds before plugging the modem in again.
Wait for the lights on the modem to light up.
Plug in your Netgear wireless router again.
Wait for two minutes. Use "ipconfig /all" again.
You should have a different IP address now.
Ping your default gateway.
At the command prompt, type "ping 192.168.1.1"
(substituting your default gateway address for 192.168.1.1).
You should receive four responses, all of which will begin
with either "Reply from" or "Request timed out."
If you receive "Request timed out," unplug your
Netgear wireless router from the power source for 20 seconds, and plug it in
again.
Wait two minutes before using "ping" again.
If you receive "Reply from" responses, check to
see if your Internet connection is working again.
Open a Web browser. In the address bar, type "http://192.168.1.1"
(substituting your default gateway address for 192.168.1.1).
Press "Enter." If you have password-protected your
Netgear router, you will be prompted for a username and password.
The default username for a Netgear router is
"admin."
When you have successfully entered the username and
password, your Web browser will show you the configuration page for your
Netgear wireless router.
If your Web browser never loads a Web page or prompts for a username and
password, you're not communicating with your Netgear router.
Double-check the address you typed into your address bar.
If you've typed it correctly and your connection is
wireless, either your wireless card has a problem or your Netgear router is not
correctly sending a wireless signal.
Make sure your wireless card is enabled (using Windows'
built-in Network Connections applet or the third-party software that came with
your wireless card).
Make sure your connection settings (SSID, security type, and
key or passphrase) are correct for your network.
Look at the lights on your Netgear wireless router.
The wireless indicator light should be green.
If it's orange or not on at all, your router is not sending
a wireless signal.
Make sure all the settings on your Netgear configuration
page are correct.
Most Internet providers use a dynamic IP address and DNS
server addresses.
Some Internet providers require a login, and some do not.
To be sure, refer to the configuration information your
Internet provider gave you when your Internet access was installed, or call
your Internet provider's technical support number.
Click on "Wireless Settings" on the navigation
bar on the left-hand side of the page.
If you were not able to reach the configuration page
wirelessly and had to connect to your Netgear router with an ethernet cable,
make sure these settings are still as you defined them when setting up your
network.
If not, either change the settings to suit you, or change
the configuration of your wireless card to match these settings.
Be sure to click the "Apply" button if you make
any changes.
Click "Router Status" on the navigation bar on
the left-hand side of the page.
Under "Internet Port," check your IP address.
If the address begins with 169.254, you're not communicating
with your cable or DSL modem. Unplug your cable or DSL modem from its power
source for 20 seconds, and plug it back in. Wait two minutes, and refresh this
page.
If your IP address still begins with 169.254, there is a problem either with
the cable connecting your Netgear wireless router to your cable or DSL modem,
or with the modem itself.
If your IP address is 0.0.0.0, there is a problem with your
Internet connection, and you should call your Internet provider's technical
support.
Record all your configuration information before trying to
reset your Netgear wireless router to the factory defaults.
Resetting may fix your problem, but it will wipe out all
your configuration information, and you will have to reconfigure your Netgear
router from scratch afterward.
To reset most Netgear routers, use the tip of a pen or an
unbent paperclip to press and hold the reset button on the back of the router
until the test light blinks.
Release the button, and wait two or three minutes.
Connect to the router's configuration page in a Web browser.
Log in with the default username and password, and configure
your router.
You may have to connect to the router with an
ethernet cable to perform this initial configuration.
SOURCE: Connecting wired Virgin Broadband through third-party WiFi Router
Clone your mac address in the router
SOURCE: Connection Failed
First, have you done a master hard reset of the router by depressing the hidden button on the back of the router?
2nd, what Operating System are you running?
Reply back and I can give you more information/instruction.
SOURCE: Wireless Computer Cant Connect to 3com router!
I just had a similar problem. Only two days after successfully using my wireless, my wireless PC did not connect but my two wired ones still did. The only radio within distance on the LAN info was called 3COM (!) but on clicking this I was told no station within range! I went to access my pages on one of my other machines but at first I made a stupid mistake by putting in the 3com access code into google, (so used to surfing with google!) instead of into the file open, or the address line! Once in, I found everything had defaulted to factory defaults. My password had gone and was back to 'admin'. My settings had all gone, so I re-did the whole thing, new passwords, new encryption numbers, the lot, saved the profile, and touch wood it is OK now. I cannot think how the whole router system would suddenly revert to default, however I did notice on the log page that just after I re-did the settings, someone tried with several computers persistently to access my broadband, but failed.
I hope this might help someone but I would be curious to know what happened. Did someone 'hack' my settings and remove them? I use WEP as I have never been able to get WAP to work.
P.
SOURCE: iPhone keeps dropping wifi signal on Netgear DG834G router.
Hi, please perform the below steps to configure settings on the router:
1. Connect a computer to the router using any one of the 4 available ports.
2. Open a web browser (Internet Explorer, Mozilla Firefox or Safari).
3. Access the router, usually with http://192.168.0.1 or http://www.routerlogin.com.
4. Login to the router with the Username as "admin" and Password as "password" (please note that the Username and Password are case sensitive).
5. Click on WAN setup from left menu. Check the box for 'Disable Dos Protection'.
6. Set the MTU size to 1400. Click apply.
I hope this information allows you to resolve this issue.
If I have helped you, please help me, and rate this suggestion the highest FixYa rating. If you cannot rate this post with the highest rating, then please comment to this post and I will try to help you further.
Regards
Anand
Had same problem - said signal weak although strong on other devices, and hung on authenticating.
Cordless phone on base unit was beside wireless router. Moved unit and turned off phone. Problem disappeared, and signal showed strong.
106 views
Usually answered in minutes!
×