Washing Machines Logo

Related Topics:

Posted on Apr 01, 2009
Answered by a Fixya Expert

Trustworthy Expert Solutions

At Fixya.com, our trusted experts are meticulously vetted and possess extensive experience in their respective fields. Backed by a community of knowledgeable professionals, our platform ensures that the solutions provided are thoroughly researched and validated.

View Our Top Experts

Sometimes there is water that fills in my washer after I use it. It does not happen right away but by the next day. I don't know the model but I do know this is an old washer....gold....I have had it for about 12 yrs and it was used before I got it....

1 Answer

Anonymous

Level 2:

An expert who has achieved level 2 by getting 100 points

All-Star:

An expert that got 10 achievements.

MVP:

An expert that got 5 achievements.

Sergeant:

An expert that has over 500 points.

  • Expert 291 Answers
  • Posted on Apr 01, 2009
Anonymous
Expert
Level 2:

An expert who has achieved level 2 by getting 100 points

All-Star:

An expert that got 10 achievements.

MVP:

An expert that got 5 achievements.

Sergeant:

An expert that has over 500 points.

Joined: Nov 23, 2008
Answers
291
Questions
0
Helped
93316
Points
784

Q - My washer seems to keep filling  with water, the water keeps coming in the washer and going out the drain without the washermotor running.
A - This often is a drain hose that is too low or a drain hose that has been pushed too far down inside the stand pipe....the water is actually siphoning out of the washer. Do not "seal" the drain hose to the house plumbing pipe, this will also allow the water to be siphoned out.

  1. Boot change helps
  2. Consumer Display Code Table on the Electronic Display Maytag Neptune Front load washer
  3. Free on-line repair manual for the Neptune washer MAH3000, MAH4000, MAH5500, MAH7500  ( Acrobat reader required )
  4. How to access the console on the mechanical timer models
  5. How to access the workings of the washer
  6. My washer door is locked and it will not open up...HELP
  7. My washer will start when I push the start button, but a few seconds later, it will shut off
  8. My washer will not pump out + pump noise problems
  9. My washer will not spin
  10. Odor complaints from the front load Neptune washer - mildew complaints + a new "freshen up" procedure
  11. Parts breakdowns/exploded of the Maytag Neptune front load washer ( mechanical timer models )
  12. Problem chart for MAH3000 & 4000 Neptune washers
  13. Readers repair tips
  14. Trouble shooting tips from the Neptune manual for MAH3000 and MAH4000 models
  15. Tips from our friendly engineer on changing the boot and re-installing that clamp and spring
  16. Tips on changing the washer belt  ( acrobat reader required ) Belt parts link
  17. Tips that show what components need to be checked/replaced if a certain resistor on machine control board is bad. It is as follows: Burnt resistors in Maytag Neptune washer models MAH4000 and MLE/MLG2000
  18. Washing one item in a front load washer
  19. Wax motor helps for the door lock assembly Sometimes there is water that fills in my washer - new25.gif
 

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

Cold water will barely flow into machine....already cleaned out strainer on incoming cold hose, water flows fine...however, once it hits the machine, it barely drips to fill up the washer. Hot water is...

bad water valve,the stuff you cleaned out of the screen most likely got inside the valve,another thing that can happen if you don't change the valve is that the valve can get stuck in an open position and it won't shut off and flood out your house.call the parts store give them the model number and they will sell you the right valve.next time send the model number and brand name,good luck.
0helpful
1answer

Frigidaire Affinity washer won't fill with water, and after a few minutes of spinning with no water, flashes an EF0 code, or sometimes an E10 code. I tried unplugging the machine to reset it, but get the...

My affinity atf8000fs1 won't fill with water. I replaced the inlet valve, pressure valve, Main board and power board and door switch. Same result. It starts, locks door, I hear clicks as if it is cycling to next phase, but water does not fill the tub. This is a front load model. Anything missed before I part it out?
0helpful
1answer

My washer fills then draind right away, so water r...

Check that the drain hose is not below the water level. If it's too low the water has no reason to stay in the machine...If the water is pumping out, you have a technical problem and will probably need a tech...Good luck....Nomess
1helpful
1answer

I have a kenmore model 110 top loading washing machine that keeps draining and wont fill up but sometimes it does and sometimes it does not. Help!

Your drain hose is too far down into the pipe behind the washer. What's happening is your drain hose is actually siphoning water from th washer the same time its trying to fill up. Pull the drain hose up from the drain pipe and secure it so its doesnt fly out when the washer is draining. Check too see if the problem goes away. If not pull the drain hose out more repeat steps.
1helpful
1answer

No water pressure on fill.

Hi, If you have checked the screens in the mixer valve and there is nothing plugging it, then it is most likely the mixer valve.
I hope this helps. Please let me know and feel free to rate my response to you.

Thanks
Vic
0helpful
1answer

Will not fill with water

It is hard to provide great guidance to you without knowing the manufacturer and model number, but I have found that some lower end washing machines will not fill or operate without the door being closed. (I know this sounds too simplistic, but this actually happened to me.)

If this does not solve your problem, please post back here and we can take the next step. OK?
0helpful
1answer

Roper washer fills with water continuously

Your inlet valve is defective, can be easily changed. Approach your dealer with your model number he will direct you to the spares shop, or tell you where you can get it. Or google 'roper washing machine spares'
0helpful
1answer

Wont fill up with water it drains out before its full

If you hear the motor running when it is draining then you have a bad timer. If it just drains out and the motor is not running then you have a siphon problem which is caused if the drain hose is too low. Let me know what you find.
0helpful
1answer

Washer will not fill

not your timer / if anything its eather the water valve or the water slector switch
Not finding what you are looking for?

643 views

Ask a Question

Usually answered in minutes!

Top Maytag Washing Machines Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Brad Brown

Level 3 Expert

19187 Answers

john h

Level 3 Expert

29494 Answers

Are you a Maytag Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...