Universal Remote control code on Sharp 13H-M60

https://www.fixya.com/support/r29872378-universal_remotes_no_facsimile_remote

https://www.google.com/search?q=lax-max+universal+remote

Sharp TV Remote codes, use the below codes to control your Sharp TV with a universal remote.

The 3 digit codes for most programmable universal remote controls for Sharp televisions are:
002
013
014
111
502
509
712
812
813
913
918
NOTE: Codes to operate televisions using a Sharp brand universal remote control will be 2 digits long. They will go from 01 to 18.

The 4 digit codes for most programmable universal remote controls for Sharp televisions are:
0039
0093
0165
0386
1004
1009
1011
1025
1064
1077
1078
1081
1097
1099
1153
1157
1274
1298
1311
1312
1362
1375
1378

..

Universal Remote Control Code Finder. Philipsuniversal remote controls can operate audio and video devices of almost any brand. For each of your audio/video devices, you have to enter a Device Code in the universal remote control.


Universal Remote Control Code Finder

www.urc.philips.com/
Feedback

GE Universal Remote Codes ' Jasco

https://jascoproducts.com/support/ge-universal-remote-codes
Note: If your remote was purchased before January 2006 Click Here for the 3-digitremote code list. Program your GE Universal Remote using the correct code list and instructions.

Universal Remote Control Codes

www.remotecodelist.com/

Hello
Setup codes for Sharp TV with Radioshak 3 in 1 remote control are:
004/009/079/095/111/112/114/122/123/124 & 173
OK.

Hello
Just buy one "Comcast Ondemand Custom DVR 3 device Universal Remote control". Sharp Tv is listed in its manual. Codes are 10093, 10165, 10386, 11602. Proceedings for setup will be there with its manual. OK.

how to enter tv codes for my magnavox tv from my sharp remote

After much searching I finally found the code list for RCR451 Universal Remote. Here are the codes for Sharp TV. 1004, 1007, 1009, 1023, 1078, 1083, 1094, 1107, 1123, 1125, 1195

have a rca universal remote with no instructions. need to use it for my tv?

http://www.remotecodelist.com/remotes/magnavox/Philips-Magnavox_PM525S.pdf
This is the user's manual for a Phillips remote control. There is a list of codes in it. They should be rather universal. There's also instructions as to how to program it. I believe that there is a way to program it without using the codes.

Programming with Code Search

1. Manually turn on the device (TV, VCR, etc.) to be controlled.

2. Press and hold Code Search button until the red indicator stays on. Release the Code Search button.

3. Press and release the desired mode button (TV, VCR, etc.). The red indicator blink, then stays lit.

4. Press the Channel Up button repeatedly (up to 300 times) until the device could be controlled changes channel. The red indicator blinks, then stays lit. If you accidentally overshoot the code required, press the Channel Down button to backtrack through the library until the device changes channel. Pressing Channel Up changes direction to forward again. Press and release the Mute button to install the code.

Hope this helps :)

Try this


complete guide to your remote solution

try out this.mash and hold the set up button.when the indacator light bilnks ,press the item in which you want coded.turn that item on by hand,point to it with remote and mash the power button up to 300 times until the item turns off.then hit enter.do not go to to fast,if you over shoot the code you will have to start all over again.let me know if this works for you. halfbreed76. e-mail mckenithfamily @net zero.com