Question about Dewalt DW056 18 Volt Cordless Impact Driver - 1/4" Drive Hex Shank (Battery Charger and Case Not Included) - Tool Only

Open Question

Dewalt DW9074 batteries go flat too quickly - Dewalt DW056 18 Volt Cordless Impact Driver - 1/4" Drive Hex Shank (Battery Charger and Case Not Included) - Tool Only

Posted by Anonymous on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How long to recharge a 18v dewalt drill battery


A fully working 18v Dewalt Battery will only take 90 minutes to just over an hour to fully charge from going flat. This fully charged battery should last about 4 hours of use (depending on the load). So the answer is 1 hour.

Aug 11, 2013 | Drills

2 Answers

Re: DeWalt 18V XRP Cordless Drill Driver. Should performance of the drill slow as battery becomes weaker? My drill works fine for quite some time then suddenly loses all power, even the light won't...


Yes. It's kind of like a flashlight when your batteries get low the light get dim, but if you replace the batteries light gets bright again. The drill will get weak as battery get low.

May 09, 2011 | Garden

1 Answer

DeWalt 18v batteries charge light flashes quickly why?


Here are the codes for Dewalt Charger Flash indications:
---- ---- ---- ---- ---- ---- ---- Charging
------------------------------------ Charged
----- - ----- - ----- - ----- - ----- Hot/Cold Pack delay
- - - - - - - - - - - - - - - - - - - Replace pack

Feb 07, 2011 | Garden

1 Answer

How do I remove the chuck on my dewalt 18 volt xrp hammer drill


Remove the REVERSE-THREAD screw at the bottom of the chuck. Set the clutch collar to the highest setting, and set the gear to the slowest setting. Remove the battery! Get the biggest allen wrench you can fit in the end of the chuck(the shortest leg) and tighten the chuck down around it, allowing the jaws to rest and tighten on the flats of the wrench. Lay the drill on its side(chuck toward you, handle to the left, and allen wrench to the left, horizontal to the deck. Then with a hammer(soft hammer if you care about the allen wrench) quickly and deliberately hit the allen wrench in an attempt to cause the allen wrench to spin counter clockwise. Let me know if this works for you, and if not, explain what is happening.

Nov 28, 2010 | Dewalt Drills

1 Answer

Proper way to charge a battery dewalt 18v battery


Always ensure it is TOTALLY Flat before charging, when charging leave totally alone for the recommended time of charge, usually a few hours, but may be up to 8. See your documentation. Always use two packs, one in use the other charging, this is the best way to get a full life from your packs.

Feb 24, 2010 | Dewalt Accessories Batteries 18 Volt

1 Answer

Dewalt batteries


did you consider the freq. hertz in your country & US.
50 to 60hz

Jul 07, 2008 | Dewalt 7.2-18.0 Volt One Hour Charger

1 Answer

Dewalt radio dw911


Have you changed the AA Batteries, this is often the fault, when they are flat they lock the radio out. HHM Dewalt Service

Nov 27, 2007 | Dewalt DC011 AM/FM Radio

Not finding what you are looking for?
Dewalt DW056 18 Volt Cordless Impact Driver - 1/4" Drive Hex Shank (Battery Charger and Case Not Included) - Tool Only Logo

Related Topics:

34 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dewalt Drills Experts

Marvin
Marvin

Level 3 Expert

85223 Answers

Lance Guthrie
Lance Guthrie

Level 1 Expert

18 Answers

Spud Howell

Level 2 Expert

66 Answers

Are you a Dewalt Drill Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...