Xerox Phaser 8560 error codes 07.010.43:203361 and 08.030.46.203361

SOURCE: Phaser 8560 error code

Most likely you are using generic ink or ink not made for that specific machine. The black ink is the one causing the problem. the printer will then need to be reset.

SOURCE: xerox phaser 8560 nvreset - how?

According to http://www.laserquipt.com/support/idx/42/615/article/-Reset-the-Printer-to-the-Factory-Defaults-NVRAM-Reset-.html (and it worked for me):



NOTE: Resetting NVRAM returns stored parameters in the image processor board NVRAMto their factory default values. The print count and the Adobe firmwareserial number are not affected by this reset. You can reset the PostScript NVRAM using the Service Tools menu or the Service Diagnostics menu.
To reset the printers NVRAM using the Service Tools menu:

NOTE: Print a Configuration Page before resetting NVRAM.
Pressand hold the [Up] arrow button on the Control Panel, and then press the[OK] button. This will automatically display the Service Tools menu onthe Display Screen.

1. Press the [OK] button.
2. Press the [Up] or [Down] arrow button to select [Reset NVRAM], and then press the [OK] button.

1. Pressthe [Up] or [Down] arrow button on the Control Panel to select[Troubleshooting] on the Display Screen, and then press the [OK]button.
2. Press the [Up] or [Down] arrow button to select [Service Tools], and then press the [OK] button.
3. Press the [Up] or [Down] arrow button to select [Reset NVRAM], and then press the [OK] button.
4. Press the [Up] or [Down] arrow button to select [Exit], and then press the [OK] button to return to the Main screen.

SOURCE: error code 09,035.43:30419 on Xerox Phaser 8560

Ink count flag stuck after melting 2.5 Cyan Ink Sticks

Check your ink sticks, one of them is most likely stuck.

marios basileiou

• 316 Answers
• Posted on Feb 04, 2010

SOURCE: xerox phaser 8560 error 04,018.48:26

Hello,this fault code indicates a problem with the process control system.The printhead temperature dropped below the head cleaning needed threshold and that's why stops warming up.The first you need to do is to verify the temperature of the room that the printer is,if its too cold,near from an open window...If was too cold and not in the room temperature then move the printer and your are done.If this doesn't solve your problem run the Monitor Heaters tests with all heaters ON.Are the heaters operating correctly?If yes replace the Electronics Module.If no you have to inspect the harness to the failed heater.Is the harness damaged?If yes you must replace the harness.If no replace the problem component.
Good luck:)

Clive

• 4362 Answers
• Posted on Mar 02, 2010

SOURCE: Xerox Phaser 8560 - error code 09 037 45 108564

Hi there

That's a ink loader error, due to the 8200 ink stick; to fix it:

- Power down the printer.
- Hold the back button and the info button at the same time, without letting go, power up the printer.
- Keep holding down the buttons until the XEROX logo comes fully to the center of the screen, keep holding for 2 more seconds, then let go. I'll take about a minute or two for the Diagnostic screen to come up, the display will turn blank and black.
- When the Diagnostic screen comes up go to down to the Function or Exercise option, there will be an option that says "clear ISC faults" it'll ask you to press OK to confirm, after you do then you will exit Diagnostics and the printer will reboot.
It should be fine until it happens again. Until all the 8200 ink is gone you will probably be doing this a few more times. Also make sure the 8200 ink is not jammed inside the ink loader, if it is then you have to un-jam it some how.

Please come back and just gave a vote, it will gave me some satisfaction to know am helping some one so I will keep on helping.

All The Best: Pineworks