Question about Mitsubishi WD-Y57 57" Projection HDTV

1 Answer

My WD-Y57 screen does not turn on. TV seems to power-up normally. Lamp 3 months old. Timer light solid green, no other lights lit. TV mechanical sounds seem normal. Looking through the vent slots in back, I can see the lamp is lit. Nothing on the display when I press the menu button. System reset button does not solve problem. If left this way the TV power stays on with timer light solid green.

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    New Friend:

    An expert that has 1 follower.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 13 Answers

You may have purchased a cheep lamp it has gone bad allready

Posted on Oct 09, 2013

Ad

6 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Lashawn Robinson

  • 1153 Answers

SOURCE: Blinking Green Light on Mitsubishi DLP 52525

No problem, do self diagnosis test, read threads here or goto ctechnicians.com get error codes first and get back with me.

Posted on Dec 17, 2007

jason

  • 905 Answers

SOURCE: Blinking Green Light on Mitsubishi DLP 52525

the circut that detects the bulb has been also failing in these sets
and the conversion chip that controls the picture , and the transformers are not putting out the full power they are supposed to.
this set will need to be tested to determine the exact cause or causes

Posted on Oct 18, 2008

Anonymous

  • 106 Answers

SOURCE: WD-62525 green timer light keeps blinking after lamp replacement

Did you let the green light flash for about 70 seconds? It goes thru a self check when plugged in and takes a little time

Posted on Dec 29, 2008

Anonymous

  • 1 Answer

SOURCE: I have Mitsubishi WD-Y57 DLP.

I have the same TV. Mine is almost 3 years old. From what I've learned you should try to reset the TV. There is a small button in the front input compartment. Use a pen to push that in and wait for the green light to stop blinking. Then try the TV.
If that does not work you probably need a new lamp. Apparently the lamps only last for a couple years on average. Having to replace them can really add to the cost of buying/owning one of these TV's

Posted on Dec 01, 2009

mustang21

  • 68 Answers

SOURCE: wd-52725 had blue screen no picture or sound

you may be on the incorrect input channel. look for an input or tv video button and choose each input until u get a picture

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/laura_08254539050d64db

Posted on Mar 03, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Code 34 replaced lamp with 2 new osram lamps may run for 5 min or 5 hrs shuts down solid red light code 34


I have a Mitsubishi model WD-60737 and to make a long story short 1st time problem lamp replaced fine for a month til my uncle hooked a DVD player to my TV next day turned on with solid green light then TV kept turning off after 2 to 3 minutes of beingetting turned on and a solid red light to show after. What does that mean? It's a brand new lamp and worked for a month so why shut down now? Could my uncle have did something to where it shook up the circuits or something?

Sep 25, 2014 | Mitsubishi WD-60737 60 in. HDTV

1 Answer

WD-57731 Will turn on, I get sound but no picture.


You should be able to see if lamp itself is lit or not, if lamp does come on or has been replaced recently let me know, I have a idea or two but need more information if possible.

Oct 14, 2012 | Mitsubishi WD-57731 57" Projection HDTV

1 Answer

I replaced the lamp however the green light blinks for a minute then the lamp light comes back on and the tv can't be turned on. WD-Y57 model


with that model after the tv shuts off pres the "menu" and "device" button on the front panel buttons together for about 8 seconds and then the power led will blink green. it will blink a certain number of times then pause and blink a different number of times this will be the error code for the fail that the tv thinks it is having. for example it may blink green 6 times then pause and blink 1 more time that would be code 61 check the code and repost and i will tell you the next course of action good luck

Jan 05, 2011 | Mitsubishi WD-Y57 57" Projection HDTV

1 Answer

I have Mitsubishi WD-Y57 DLP. Replaced lamp and now green timer comes on for a minute or so and then turns off. TV will not come on?? HELP!


I have the same TV. Mine is almost 3 years old. From what I've learned you should try to reset the TV. There is a small button in the front input compartment. Use a pen to push that in and wait for the green light to stop blinking. Then try the TV.
If that does not work you probably need a new lamp. Apparently the lamps only last for a couple years on average. Having to replace them can really add to the cost of buying/owning one of these TV's

Nov 21, 2009 | Mitsubishi WD-Y57 57" Projection HDTV

1 Answer

No picture with sound


yes , u need a new lamp shop around , cost less

May 08, 2009 | Mitsubishi WD-Y57 57" Projection HDTV

4 Answers

Mitsubishi WD-62525 timer light keeps flashing after lamp replace


There is a tiny reset button to the left of the timer light. Press with a pin or something small, wait 60 seconds. Viola!

Dec 29, 2008 | Mitsubishi WD-62525 62" Rear Projection...

1 Answer

TV will not turn on


There are a few reasons that this could be happening first one is maybe the lamp died on you, Afraid there is no way to test this other than replacing the lamp. The second problem may be 5 capacitors on the power supply that hold the 12 volt line low and do not allow the light engine to start properly.
First thing you have to do is listen to how it trys to start, It should sound like this, first when you hit the power switch there may be a click then within five seconds the fans then a few seconds more you may here a sparking noise, if all this is happening then you most likely just have a bad lamp

Feb 19, 2008 | Mitsubishi WD-52725 52". Rear Projection...

Not finding what you are looking for?
Mitsubishi WD-Y57 57" Projection HDTV Logo

218 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Televison & Video Experts

matt martin
matt martin

Level 3 Expert

1257 Answers

The Knight
The Knight

Level 3 Expert

76173 Answers

Ekse

Level 3 Expert

13434 Answers

Are you a Mitsubishi Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...