Lg 32cs560 power indicator falshing red then blue once and shuts off

Hi, Ephraim. The flashing red light indicates that the device is showing "low battery". It could be that the LG phone charger fits the charging port on your bluetooth headset but it is not compatible with your device. In order for you to know that it is charging, the device should show a steady red light(means charging).
Please take a look at the table reference below.
----------------------------------------------------------------------
•With the Charger Plugged In
______________________________________________________________________
•Headset Indicator Headset Status
Red-----------------------------------------------Charging (battery level less than 50% charge)
Yellow-------------------------------------------Charging (battery level more than 50% charge)
Green--------------------------------------------Charging complete
----------------------------------------------------------------------
======================================================================
======================================================================
======================================================================
----------------------------------------------------------------------
With No Charger Plugged In
__________________________
Headset Indicator Headset Status
______________________________________________________________________
Off ---------------------------------------------Power off
Three blue flashes------------------------Powering on/off
Steady blue --------------------------------Pairing/connect mode
Rapid blue/purple flashes -------------Connection successful
Quick blue flash --------------------------Incoming/outgoing call
Slow blue pulse --------------------------Connected (on a call)
Slow blue flash ---------------------------Standby (not on a call)
Slow red flash ----------------------------Idle (not connected to phone)
Slow purple pulse -----------------------Connected call muted
Steady red ---------------------------------Attempting to connect
Quick red flash ----------------------------Low battery

Note: After 20 minutes on a call or of inactivity, the light stops flashing to conserve power, but the headset remains on
----------------------------------------------------------------------

Hope that'll help you in some way.
**Please rate my post and/or leave a comment** ...Thanks...

Press the Settings button on the remote or touch the Settings button on the front panel. You may download a copy of the manual from http://www.lg.com/us/support-product/lg-32CS560#

You may download the manual from http://www.lg.com/us/support-product/lg-32CS560#

Look for changes in settings.

First disconnect all power to the TV for about 30 minutes this gives the filter caps time to discharge as this resets the logic section upon power-up. After 30 min try powering back up if you still have the same problem then there's a problem with the power supply board. You may have some caps with high ESR levels which can cause this kind of fault. But it could other components on the power board causing a similar fault like switching transformers that have shorted, or opened either which can cause EDDY Currents which will cause feedback in opto-couplers and shut the TV down. Let me know what results you get after the 30 minute power-down.

LED Indicators - LaCie 2big Network
The LED indicators above the drive bays and the front LED indicate drive status and activity.
During Startup

• Front LED – blinks red/blue until both disks are powered on, then turns solid blue.
• Rear LEDs – blinks red/blue until corresponding disk is powered on, then turns solid blue.

NOTE: If the device is not able to initiate the boot process following disk startup, the front is solid red.
During Bootup

• Front LED – solid blue
• Rear LEDs – solid blue

NOTE: If a disk is failing, both the disk’s corresponding rear LED and the front LED will be solid red.
During RAID Synchronization

• Front LED – solid red
• Rear LEDs – The LED corresponding to the original disk will be blinking blue and the one being synchronized is blinking red
• Once both disks are synchronized, their corresponding rear LED and the front LED will be solid blue.

Ur power board need it replaced,LED indicator light not sustaning power.

There are two places to look for the problems, the backlight inverter board and the power supply. Look at the power supply first since it is easier to get to, look for burnt parts, bad capacitors, etc.
http://en.wikipedia.org/wiki/Capacitor_plague
Please post back what you find.

I have a similar switch on mine, although mine is a Gateway. So my solution is going to assume the same indicators and functionality.

On mine, a blue-violet power switch indicates it is off, red indicates standby mode, and blue to indicate it is on and/or searching for a signal. When turned on (blue), the monitor will go to standby mode (red) after 3 to 4 seconds if it does not detect a source signal. So if you toggle the power switch to blue and it soon changes to red, you'll need to check your signal, cable, or possibly for a bad source connection on the monitor.

Hi Altus

This a common Mainboard failure on the LG JT91 if all the LED's flickers.

The good news is that it can be repaired. Much cheaper than replacement.

This will however have to be done by a Service Provider.