Question about Xerox DocuPrint N40 Laser Printer

1 Answer

Asterisks in display

When powering on the printer, printer initalizes. It displays the "version" and it doesn't appear that any faults occurs. Then a single "*" apppears in the display. A short time later the display fills with "*"'s and the on-line indicator goes green, but the printer goes no further. The asterisks stay in the display and the "READY" state is never reached.The printer was working fine until netware was disabled and the printer re-booted.

Posted by on

  • PrinterSlave Jun 06, 2008

    My Xerox DocuPrint N40 several times jamed first. But it made this broken gear noise after I took out the last jammed sheet. I removed the tone cartridge and the fuser to see if I could see any broken or damaged gears. I found none. I put all the parts back and shut the door, no noise started. One minute later I looked at the screen and saw "Sys ERR OU476 Power Off & On" on the display screen. I restarted the printer. First a single * appeared, then followed by several * in a row and then it returned to the "Sys ERR OU476 Power Off & On" with the Online & fault lights on as well as a blinking Data light.

×

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Had the same problem: took the tray away and found a sheet of paper in the printer not alawing
the tray sensor to work properly!!! after that the prob was solved.

Posted on Oct 14, 2008

Ad

1 Suggested Answer

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to factory reset the hp pro 300 laserjet printer


1. Power down the printer
2. Press and hold the lower left hand corner of the screen
a. This is normally where the progress bar starts loading on the screen
3. Power on the printer
4. Release the left hand corner once the "Permanent Storage Init" message appears.


or alterative way
1. Power down the printer
2. Press and hold the right arrow button on the navigational bar
a. This button will flash for a moment when the printer boots up
3. Power on the printer
4. Release the left hand corner once the "Permanent Storage Init" message appears.

Jul 14, 2016 | HP Office Equipment & Supplies

1 Answer

Cannot fax out and cannot receive, says memory is low


Please perform the following:
Super NVRAM init
When a super NVRAM init is performed, the all-in-one language and telecom country/region settings
are undefined. The user is prompted to set the language and telecom country/region. Until these settings
are defined, the all-in-one will not return to the Ready state.
CAUTION A Super NVRAM init erases all data that is stored in both the unprotected and
protected NVRAM memory.
To perform a super NVRAM init
1.
Turn off the all-in-one.
2. Press and hold down the * and 5 buttons.
3. Continue to hold down the buttons while you turn on the all-in-one. Hold the buttons throughout
the entire power-on sequence.
4. When Permanent Storage Init. appears on the control-panel display, release the buttons.
5. When prompted, set the language and telecom country/region.
6. Allow the all-in-one to return to Ready before using it.

Mar 18, 2011 | HP LaserJet 3055 All-In-One Printer

1 Answer

HP Laserjet 4345MFP Backlight on printer display does not light. Counts up the 256MB memory then HP logo (3 sizes) appears (just visible) The 3 lights keep cycling on the display. Thats it, does nothing...


HP Laserjet 4345MFP
Backlight on printer display does not light.
Counts up the 256MB memory then HP logo (3 sizes) appears (just visible)
The 3 lights keep cycling on the display. Thats it, does nothing else.
It has been left overnight and continues to display the logo and cycling 3 lights.
Rear DC Cont Fan is turning. No other fans or activity with machine.
When ADF/scanner/mfp or hard disk are disconnected it does recognise this and throws an error and asks for reboot.
I have tried cold reset, nvram init. and hard disk init. but no difference.
Your thoughts?

Aug 27, 2010 | HP LaserJet 4345mfp Printer

1 Answer

My canon ip1980 appears error 5100 on my display i will replace my data strip but the problem still occurs. What should i do. Tnx


This problem is between waste ink absober full and ink cartridge.
Firstly your need to reset waste ink absober full.
Follow this step to reset waste ink absober full.

1> download iptool to reset waste ink absober full
Download here ----> Service tool 1
Service tool 2

After ypur download finish
> turn off your printer power switch
> open your printer cartridge door
> press and hold on/off button (never release)
> turn on printer power switch
> push your printer cartridge door switch with pen or anything can press that door swith.
> then release on/off button
> close open door
> then press on/off button 1 more
now your printer is in normal mode( no orange led blinking)
Then you can use ip service tool to permanent reset waste ink absober full.
----------------------------------------------------------------------------
IF after reset your waste ink absober full, problems still apppear error5100
> change your ink cartridge with the working cartridge

usually error e5100 due tow problems above

Hope this guide can help fix your problems

Extra download
Fixwasteinkabsoberflow



Jun 23, 2010 | Canon PIXMA iP1800 InkJet Photo Printer

2 Answers

Error code 6


-switch off the printer, then remove all cables connecting to the printer but just the power cable.
-then press and hold the *(start/symoble) and 5 button togather and turn on the printer.
-continue holding the button till you see "perment storage init" displayed and releas the button.
-then at a given point of time the printer will ask you to change laguage,time,date etc.
if this does not sort the issue service is required.

Aug 25, 2009 | HP LaserJet 3055 All-In-One Printer

2 Answers

49.4401 service error on start up


Solution or Workaround:

1) TRY to flash the firmware.
2) Try cold reset and disk initializations.
3) Replace firmware dimm.
If you have a hard disk:
To resolve the issue it may be necessary to perform the Disk Init procedure.

Disk Init Procedure
1. Turn the printer off, then on
2. When the memory count starts on the control Panel, press and hold the Menu button until all 3 lights on the control panel are lid
3. Press the < button. The message “INITIALIZE DISK” appears in the display
4. Press the Check button. The printer will initialize the User space on the Compact flash and will continue it’s power-on sequence.

If I could be of further assistance, let me know. If this helps or solves the issue, please rate it.
Thanks, Joe


I’m happy to assist further over the phone at https://www.6ya.com/expert/joe_8b8c2cd6ce148309

May 19, 2009 | HP LaserJet 4650dn Printer

1 Answer

Elevation has gone too high. foot rollers are hitting front plate


Precor Error E4, Incomplete Initialization Probable Cause Indicates that an incomplete upper PCA to lower PCA initialization occurred. When this error occurs, all lift motor and drive motor motion is ceased and the display will go blank except for the error displayed.
Corrective Action Run the initialization program. Caution: The treadmill's running belt will accelerate to the treadmill's maximum speed (12mph). DO NOT stand on the treadmill's running belt during the procedure.
  1. Set the on/off switch to the OFF position. Wait a minimum of 10 seconds to allow the internal power supply to discharge.
  2. Remove the safety key from the console and set the on/off switch to the ON position.
  3. Press INCLINE UP and SPEED DOWN keys together. While pressing these keys, replace the safety switch on the console. Continue holding the INCLINE UP and SPEED DOWN keys until the display goes blank. INIT will appear in the time window of the display. The EEPROM is now clear and reset. After a second, 1.25 will appear in the distance/calories window, 15.0 (the maximum incline) will appear in the incline window, and 12.0 (the maximum speed) will flash in the speed/pace window.
  4. Press QUICKSTART to begin the speed calibration process. Power bits will appear in the incline window, the target speed will appear in the time window and the actual speed will appear in the speed/pace window. At the beginning of the process, the target speed will be .5mph. The running belt will start. Once the actual speed reaches .5mph, the target speed will then change to 12mph and the running belt will accelerate until it reaches 12mph, then it will stop.
  5. When the running belt stops, the display will return to the user mode and the initialization process is complete.

Precor Error Code E4

Apr 30, 2009 | Precor EFX 546i Elliptical Version 4

1 Answer

After i dial a number the machine is showing "MEMORY LOW" on display unit, how to solve the problem ?


Hello,

Please perform the following:

Super NVRAM init
When a super NVRAM init is performed, the all-in-one language and telecom country/region settings
are undefined. The user is prompted to set the language and telecom country/region. Until these settings
are defined, the all-in-one will not return to the Ready state.
CAUTION A Super NVRAM init erases all data that is stored in both the unprotected and
protected NVRAM memory.
To perform a super NVRAM init
1.
Turn off the all-in-one.
2. Press and hold down the * and 5 buttons.
3. Continue to hold down the buttons while you turn on the all-in-one. Hold the buttons throughout
the entire power-on sequence.
4. When Permanent Storage Init. appears on the control-panel display, release the buttons.
5. When prompted, set the language and telecom country/region.
6. Allow the all-in-one to return to Ready before using it.

Enjoy the solution.
Nikhil Gedam

Dec 15, 2008 | HP LaserJet 3050 All-In-One Printer

1 Answer

52 scanner error problem


Hello,

Perform the following:
Super NVRAM init
When a super NVRAM init is performed, the all-in-one language and telecom country/region settings
are undefined. The user is prompted to set the language and telecom country/region. Until these settings
are defined, the all-in-one will not return to the Ready state.
CAUTION A Super NVRAM init erases all data that is stored in both the unprotected and
protected NVRAM memory.
To perform a super NVRAM init
1.
Turn off the all-in-one.
2. Press and hold down the * and 5 buttons.
3. Continue to hold down the buttons while you turn on the all-in-one. Hold the buttons throughout
the entire power-on sequence.
4. When Permanent Storage Init. appears on the control-panel display, release the buttons.
5. When prompted, set the language and telecom country/region.
6. Allow the all-in-one to return to Ready before using it.

If this step does not resolve the issue, please repair/replace the printer.

Nikhil Gedam

Dec 11, 2008 | HP LaserJet 3050 All-In-One Printer

2 Answers

Noise(grinding), can't print, can't receive fax, multiple prints


is there a error message in the display, ley me kno what it is and i will try and help - brother tech

Nov 20, 2008 | Brother MFC-8440 All-In-One Laser Printer

Not finding what you are looking for?
Xerox DocuPrint N40 Laser Printer Logo

Related Topics:

87 people viewed this question

Ask a Question

Usually answered in minutes!

Top Xerox Office Equipment & Supplies Experts

Tareq Bin Mostaq...
Tareq Bin Mostaq...

Level 3 Expert

1449 Answers

CheckitRight
CheckitRight

Level 3 Expert

1363 Answers

Philip Hughes

Level 2 Expert

80 Answers

Are you a Xerox Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...