Question about Amana Freezers

1 Answer

I have an amana refrigerator model #sxd22s2w. The ice cube dispencer and the water dispencer are working .The water is not going through to the dispencer I had the water valve checked and was told it works. I was told I need to have the dispencer checked. I tried to remove the dispencer by removing three screws, but I cannot remove it. Is there another screw that has to removed? Also How do I disconnect the wiring?

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Cheetah:

    An expert who has answered 20 or more questions within one hour.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 173 Answers

Seems like a clog somewhere calcium deposits

Posted on Mar 18, 2019

Ad

6 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
voodoomox

marlon john madrid

  • 1689 Answers

SOURCE: Door handle has come loose

re-attaching the door handles will require you to dettach the front door cover from the actual front door (as shown on the "parts manual") some of the units circuit may run through the door so be careful in removing the front door cover.
once it is removed, the handle mount will be exposed, place the screws if need and use compatible bushings to make sure the screw will be locked in place.

refer to the link below to get the Parts Manual and the Wiring diagram of your firdge.

http://www.frigidaire.com/support/ResultsPage.asp?strModel=FFU14K2CW&User=&Search=Search

good luck, i sure hope you get this one working in no time.

-voodoomox

Posted on Jul 28, 2008

Anonymous

  • 2 Answers

SOURCE: Freezer not working

I have a Kenmore Freezer model # 253.9251310 serial # s510347256
10\95 Makes all kinds of noises and now is defrosting. Sounds like fan is working but no noises besides fan. any ideas

Posted on Dec 12, 2008

Kgt1962

Kenneth Turnbull

  • 59 Answers

SOURCE: GE top freezer refrigerator automatic ice cube

If it is leaking water in the freezer it will more than likely freeze amongst the ice cubes causing a block of ice.

It is more than likely leaking at the rear of the unit, near the valve or fill tube for the ice, this will run up the rear wall of the unit.

Posted on Mar 13, 2009

jumptrout51

steve

  • 3361 Answers

SOURCE: frozen water on the bottom of my Amana freezer

Your drain line is clogged. Take a small diameter pice of wire and snake out the drain line from inside the freezer.
You may have to access the back rear near the compressor and separate the drain line there and clean it further.

Posted on Apr 07, 2009

Anonymous

  • 68 Answers

SOURCE: Chest freezer lid repair

if your freezer has the sping etc in each of the hinges, then yes take them off. If your freezer has a torshon bar type spring, DO NOT take the hinges off, as you will not get it back together

i have always replaced liners with the door attached. The lid of the freezer is going to bow out of shape when you remove all the screws and take the old lining off, so you need to replace the lining and leave the screws loose so you can realine the door bit by bit.
it is a bastard of a job, and i wish you all the best.

Posted on May 02, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Maytag MSD2651KES delivers crushed ice but no cubed


There is an metal arm that extends out behind the ice bucket that moves up and down when you press the cubed/crushed ice buttons. You need to take the ice bucket out and check the hardware. It's possible that some ice has managed to form in the unit and are blocking the motion. Remove any ice and check if the arm moves freely when you press the buttons on the refrigerator. Similarly, you should check if there is ice blocking the forward and back motion of the plunger in the freezer that bar sits on. This plunger is right next to the auger motor.

http://www.searspartsdirect.com/partsdirect/part-model/Maytag-Parts/Refrigerator-Parts/Model-MSD2651KES/3048/0165000/W0703730/00013 has a picture of the ice bucket parts.

Dec 06, 2013 | Freezers

1 Answer

Ice maker will not separate ice cubes


Check if your water filter is up to date, if not check if the ice maker has the option to choose the side of the ice cubes, if so, set it up to medium side.

Apr 05, 2013 | Samsung RF217ACPN - 20 cu. ft. French Door...

1 Answer

We have a Jenn-Air Refrigerator/Freezer (Model #JRSD226) and the ice maker has stopped working.


Check for blockage in the water line in the freezer. If so, defrost it. Might need a new water valve. Maybe a bad ice maker too.
Another possibility is that it's not cold enough in the freezer. Should be below +10F.

Freezer repair in Corona Del Mar, CA
Appliance repair in Corona Del Mar and Orange County, CA

Jan 25, 2011 | Jenn-Air Freezer Jenn Air Clear Cube Ice...

1 Answer

Our subzero freezer has a new problem. The cubes


Ice cubes WILL BE slightly moist when they land in the ice bucket. they've just been slightly melted in order to eject from the ice maker. Stop playing with the settings, for starters. put them back to normal, i.e., middle setting, place thermometer in center of freezer, and if you can, one in center of fresh food. monitor after 24 hours, and for the next three days thereafter. freezer temps should be in the -5 - +5°F, sometimes up to 10°, fresh food should be 35-40, sometimes up to 44°at the normal settings. If you are not having temperature issues, see if you notice any frozen drips of water on the underside of icemaker, indicating a possible crack in the ice maker mold, or a faulty water valve. You didnt include your model and serial number, so not knowing the path of the ice shoot, some go out the freezer door, some slide over and get dispensed from the fresh food side. Its possible you may have a problem instead with the flapping door that opens to allow ice cubes to be dispensed, or similar type mechanism. If this door does not seat completely when its closed, it will leak warm air directly into the ice bucket, which would make them slightly moist, also too, this warm air can cause frost and ice to buildup near the warm air source...look for any unusual forms of ice and or frost leading up from the flapping door to the ice bucket. Also look for any gaps in the door gasket when closed, this warm air leak can also cause similar problems, but its most likely with the ice door. could be the door, the spring, the solenoid, or something else i wouldn't know without personal refrigerator inspection.

Mar 27, 2010 | Freezers

1 Answer

Fridge Freezer model KA58NP90 Ice maker problem


What is most likely your problem is the crushed ice solenoid. This solenoid, which is located next to the auger motor behind the ice bucket, is failing to actuate when you request cubed ice. Its "home" setting is crushed, and actuates to allow cubes past the crushing mechanism in the bucket. To be certain its the problem, remove the ice bucket, and tape the door light switch in the closed position. actuate the ice dispenser lever, for both cubed and crushed ice. you will see a square hole next to the rotating fork, when you select cubes, it should open. If it does open, there is something wrong with your ice bucket, perhaps the arm is broken, or the door inside bucket is off its snap in type hinge or broken altogether. If it doesnt open, replace the solenoid

Expert Refrigerator Repair Service in Chicago and Suburbs

Mar 20, 2010 | Freezers

1 Answer

Doesn't make ice cubes. Water doesn't come in.


Hello it sounds like the timer on the ice maker may be the cause. If you open the freezer when the fan is off raise and lower the arm on the ice full shut off. listen for a faint clicking noise you wont hear if fan is going. If it does not click the problem is going to be in the actual switch. I have repaired several with this same problem with the switch but you would probably rather invest in a new ice maker or either buy some trays. As the ice makers can cost up to 200 dollars in some models. The only other thing to check is if the water line is bent or crimped off.

Jan 27, 2010 | Jenn-Air Freezer Jenn Air Clear Cube Ice...

1 Answer

Kenmore ice maker problem


the problem is an unlevel icemaker to prove this do you see little droplets of water freezing from the icemaker or a remote possibilty is do you have to an R/O system and have you change the filter if unit has one.

Aug 19, 2009 | Kenmore Freezers

1 Answer

GE TBX21ji Refridgerator/Freezer Factory Icemaker quit making ice


Normally, when the temp of the icemaker gets to about 14 degrees F, the icemaker goes into the harvest mode, turning on the mold heater and attempting to eject the cubes. When the heater has warmed the mold sufficiently to release the cubes, the ejector can continue and push out the cubes, then the icemaker fills with fresh water to beging to make a batch of ice again. Manually starting the cycle as you have done only allows the cycle to start without the temp sensor seeing the 14 degrees. The mold heating generally takes a couple minutes. If your mold heater or the temp sensor are not working, you will have to replace the icemaker, as they are not available as a repair parts.

Jul 04, 2009 | Freezers

1 Answer

Thin Ice on Whirpool Ice Maker


Hi

If  The ice maker has completely stopped producing ice Check to see whether the ice maker has been turned off. Here's how to check. Look for a wire along the right side of the ice maker that looks a bit like a coat hanger. If this wire is in the raised position, the ice maker is turned off. On some units you simply lower the wire to the down position to turn the ice maker on. On others, you lower a small red plastic lever to lower the wire. If the wire is in the proper position check the freezer temperature, it should be between 0-8 degrees Fahranheit. If it is warmer than 10-12 degrees, the ice maker may not produce any ice. Check your door seals and thermostat, repair/replace as necessary.

The ice maker is producing ice poorly When an ice maker is producing ice poorly--when it produces just a few cubes or none, or when the cubes are too small--it's usually because of a clogged water line or a defective water inlet valve. 

First, check the water line attached to the back of the refrigerator for good water flow. To do that, first turn off the water supply valve. Then remove the water line from the back of the refrigerator. Next, place the water line into a bucket and momentarily turn the water valve back on to test the flow. If the flow is poor, you need to repair, clean, or replace the tubing or the shut-off valve that supplies the water. If the flow is good, you may have to replace the water inlet valve.


Please do rate the solution as "FixYa" if found useful and revert for further assistance.


Thanks
Rylee

Apr 05, 2009 | Whirlpool Freezers

1 Answer

GE top freezer refrigerator automatic ice cube maker leaks water into the freezer, and eventually on the floor. Water seems to be coming from the area that fill up to make more ice cubes.


If it is leaking water in the freezer it will more than likely freeze amongst the ice cubes causing a block of ice.

It is more than likely leaking at the rear of the unit, near the valve or fill tube for the ice, this will run up the rear wall of the unit.

Mar 12, 2009 | GE Freezers

Not finding what you are looking for?
Freezers Logo

Related Topics:

994 people viewed this question

Ask a Question

Usually answered in minutes!

Top Amana Freezers Experts

John Tripp
John Tripp

Level 3 Expert

4656 Answers

Dennis Boxerman

Level 3 Expert

1300 Answers

Gil Shultz

Level 3 Expert

3388 Answers

Are you an Amana Freezer Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...