Sharp VCR - Multi-Brand VCR - Need Samsung TV Code for it.

Hello
Three digit universal remote codes for Sharp TV are:
004/ 009/ 079/ 095/ 111/ 112/ 114/ 122/ 123/ 124/ 173
Four digit universal remote codes for Sharp TV are:
0079 0123 0063 0020 0004 0009 0226 0266 0006 0095 0122
Direct Code Entry

1. Press and hold the SETUP button until the red indicator stays on, then release the SETUP button.
2. Press and release the desired Mode button (TV, VCR, etc.). The red indicator blinks, then stays lit.
3. Enter the 4 digit code from the code tables. Note: after a valid code entry, the red indicator turns off. For an invalid code, the red indicator flashes.
4. With your device on, press CHANNEL UP. If the device responds, no further programming is required. Note: If some buttons do not operate your device, try one of the other codes for your brand.

OK

Here you go:

http://tv.manualsonline.com/manuals/mfg/sharp/sharp_vc_h993u_vch993u.html

Unfortunately if there is no menu option to do that or button on the VCR you will need one of these remote controls

http://www.replacementremotes.com/SHARP/Buy-RRMCG1236AJSB-VCR-Remote-Control.html

or

http://www.replacementremotes.com/SHARP/Buy-RRMCU0002AJZZ-Remote-Control.html

There are two devices that need to be identified; the remote brand and model and the VCR brand and model. Giving us only one is useless. Secondly, there may not be any code set in the remote compatible with your VCR. Universal remotes aren't universal.

The codes to use for a Sharp VCR and a URC-3021 are 0048 or 0807.

To setup your URC-3021 for the VCR, these are the steps:

1. Turn on your VCR .
2. On the remote control, press VCR once.
3. Press and hold SET until the LED (red light) blinks twice,
then release SET.
4. Enter the first four-digit code for your device. If performed correctly,
the LED will blink twice. If the LED did not blink twice, repeat steps 2 through 4 and enter the same code again.
5. Aim the remote control at the device and press POWER once. The device should turn off.

Hope that helps.

All I am looking for is the owners manual and a remote control for the VCR I purchased at Goodwill--Sharp model VC-H822.
Thank you and have a great day.
David

http://www.oneforall.com

Hope this helps.
Len

Check e-bay for SHARP RRMCG1236AJSA TV/VCR REMOTE

There are some for under $10 total

How to program the remote to your TV

It took me a week to find the right instructions and codes on how to do this so I am posting it everywhere I can to help out folks with the same remote. Pay close attention to the instructions, for instance when programming the remote for TV use make sure you hold the TV button down while you enter the code and then press OK, You also have to hold the TV button down while you use the volume and channel controls or it will just change the VCR channel.
===========================================


A
Turn on TV

Turn on the TV using the Power button on the TV or its Remote.

B
Set TV brand code

A
Press and hold TV.
B
Press MBR SET.
C
Press the Number keys to enter your TV.s brand code.
D
Press OK, and release TV. The TV should turn off.


C
Operate TV

While holding down TV, press one of the following buttons:
POWER 1, TV/VCR, TV CH+/., ^(TV Muting), TV VOL+/.,
and the Number keys.

.
For some brands, you must press ENTER after having pressed the
Number keys to enter a channel number.
TV BRAND CODE TV BRAND CODE
JVC 01, 03
SONY 07
HITACHI 10
SAMSUNG 12
MAGNAVOX 02
SANYO 13
MITSUBISHI 03
SEARS 13
PANASONIC 04, 11
TOSHIBA 08
RCA 05
ZENITH 09
SHARP 06

Cable Box or DBS Receiver Brand Setting

A
Turn on cable box or DBS receiver

Turn on the cable box or DBS receiver using the Power button on
the unit or its Remote.

B
Enter brand code

A
Press and hold CABLE/DBS.
B
Press MBR SET.
C
Press the Number keys to enter your cable box.s (or DBS


receiver.s) brand code.
D
Press OK, and release CABLE/DBS.

C
Operate cable box or DBS receiver

While holding down CABLE/DBS, press one of the following
buttons: POWER 1, TV CH+/., and the Number keys.

.
For some brands, you must press ENTER after having pressed the
Number keys to enter a channel number.
.
To change the cable box.s (or DBS receiver.s) channels, press TV
CH+/–
or the Number keys. (The CH+/–
button can be used to
change the VCR.s channels only.)

CABLE BOX BRAND CODE
ARCHER 01, 05, 17
CABLETENNA 01, 17
CABLEVIEW 15, 16, 17, 21, 25
CITIZEN 15, 16, 17, 21, 25
CURTIS 02
DIAMOND 01, 17
GC BRAND 15, 16, 17, 21, 25
GEMINI 15
GENERAL INSTRUMENTS 01, 04, 06, 11, 12, 15, 28
HAMLIN 10, 18, 23
JASCO 15
JERROLD 01, 04, 06, 11, 12, 15, 28
NOVAVISION 02
OAK 07
PANASONIC 13, 14
PULSER 15, 16, 17, 21, 25
RCA 13, 14
REGAL 10, 18, 23
REMBRANDT 01, 16, 17
SAMSUNG 05, 16, 24
SCIENTIFIC ATLANTA 02
SIGMA 07
SL MARX 05, 16, 17, 24, 25
SPRUCER 13, 14
STARGATE 05, 15, 16, 17, 21, 24, 25
TELEVIEW 05, 16, 24
TOCOM 01, 04, 16
UNIKA 01, 17
UNIVERSAL 16, 17, 25
VIDEOWAY 03, 09, 22
ZENITH 03, 09, 22
DBS RECEIVER BRAND CODE
JVC (DISH Network) 51
ECHOSTAR (DISH Network) 51
SONY (DSS) 41
RCA (DSS) 40

Changing Remote Control Code

This Remote is capable of transmitting two control codes; one set
to respond to A code control signals and another set to respond to
B code control signals. This Remote control is preset to send A
code signals because your VCR is initially set to respond to A code
signals. You can easily modify your VCR and the Remote to
respond to B code signals. When using two JVC VCRs, set two
VCRs and their Remotes to different codes, so that you can
operate these VCRs separately.

A
Set remote control code for Remote

A
Press and hold A/B.
B
Press the Number key .2..
C
Press OK, and release A/B.


.
The Remote now can transmit B code control signals.
B
Check remote control code for VCR

Press and hold 4
on the VCR for more than 5 seconds while the
VCR is turned off. The code currently set appears on the display
panel.

C
Change code for VCR

Press any key on the Remote. The VCR now responds to B code
control signals.

.
To set the Remote and the VCR back to A code control signals,
repeat the same procedure as shown above except pressing the
Number key .1”
in step B
of 1
1111.
To control two VCRs with the same Remote

You can control two JVC VCRs by switching the remote control
code for the Remote between A and B (.
step A
AAAA), keeping two
VCRs to different control codes.

.
To change only the remote control code for the Remote, DO
NOT perform steps B
BBBBand C
CCCC.
—