At Fixya.com, our trusted experts are meticulously vetted and possess extensive experience in their respective fields. Backed by a community of knowledgeable professionals, our platform ensures that the solutions provided are thoroughly researched and validated.
- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
IF your Laptop has a stereo LINE 1/8" INPUT jack, you can take the Stereo ( Left & Right ) LINE outputs on your mixer and feed into this jack on your PC. You will need a 1/4" dual plug for the mixer end to a single 1/8" stereo plug on the PC end. I suspect the problem you are having is either related to your PC only have a MIC input jack or you have something set wrong in your PC's sound config. file. More information is needed to properly solve the problem.
Sounds to me like either an open wire or a blown speaker. I would highly recommend not operating it until it is fixed before you blow the amp. Tapping a 9V battery across the speaker (disconnected from amp) will cause a noise in the speaker, if not it is a broken wire or bad speaker. Good Luck
Hi,
A. As you have stated that "music plays just fine" and
you also said that "there is absolutely no sound", so I am a little
confused on this issue. Could you clarify whether you get any sound
while playing a song/video on Windows Media Center
or is it an issue only with the navigation sounds on Windows media
Center?
B. You may check the Volume mixer settings for the Windows Media Center.
Cross check the settings.
Here is how:
1. Right click on the Speaker icon on the task bar.
2. Click on "Open Volume mixer".
3. In the Windows Media Center mixer drag the slider down till you get the adequate sound.
All sound equipment has to operate without overloads in any given place. The power source should always be examined at commercial gigs and worked out with other performers along with management. The only fix is to do these checks up front and make safe arrangements.
If you are experiencing a mid-range humming from your monitors when using your Allen & Heath PA12-CP mixer, there may be a problem with the signal level or the cables.
Here are a few steps you can try to troubleshoot and resolve this issue:
Check the signal level of the sources that are being sent to the monitors (e.g. kick drum, snare, etc.). Make sure they are not too loud or too quiet, as this can cause the limiter to engage and create a humming sound.
Check the cables that are connected to the monitors. Make sure they are not damaged or loose, and that they are properly connected to the mixer and the monitors.
Try using a different set of monitors to see if the problem persists. If the humming is still present, the problem may be with the mixer itself.
If you are still experiencing a humming sound, you may need to contact Allen & Heath customer support for assistance. They will be able to provide you with more detailed troubleshooting steps and help you resolve the issue.
Overall, if you are experiencing a humming sound from your monitors when using your Allen & Heath PA12-CP mixer, the problem may be with the signal level, the cables, or the mixer itself. Follow the steps above to troubleshoot and resolve the issue.
No reason to worry about getting signal to the LED's... you set the trim gain so the loudess sound or signal that can happen barely clips or is slightly less. That is the starting point. Watch videos on mixer setup on YouTube. DOn't worry if their mixer is different as the principles are the same.
Mixer fadrs should be around 80% up when system is balanced. ALWAYS use BALANCED cables... eithrt XLR or TRS.
Hi,
you can't just plug and play with these high end mics. You require a +48v phantom power source from something such as a mixer. Then plug the mic into the mixer and the mixer into the LINE IN on the PC
hi, check the power outlet socket to which the amp and mixer is connected. if there is any loose contact in that power socket, this problem can occur. try to use a good surge protector with emi filter for connecting the amp and mixer. ok
you need to re-install your sound drivers. if problem presist, it might need to replace sound card, if sound card is built on motherboard, you may need to purchase a new PCI sound card from market.
×