Life Fitness 9500HR Next Generation Remanufactured Treadmill Logo

Related Topics:

A
Anonymous Posted on Dec 29, 2013
Be the first to answer

9500HR incline stuck - Life Fitness 9500HR Next Generation Remanufactured Treadmill

Answer This Question

2 Related Answers

gymtech

Ronnie Pelton

  • 18 Answers
  • Posted on Feb 09, 2010

SOURCE: Hi! i have a life fitness 9500HR treadmill and it

Unplug the treadmill . Remove front cover. On the right hand side if you are facing the front - in the siderail is a white switch that tells the treadmill it is all the way down. Check that it is in place and clean.
If you plug the treadmill in.{Do not touch any thing in the motor compartment} When you press start it should go all the way down [home] to contact the switch. You can also see the lit motor turn at this time before the belt will move it must be all the way down.

Ad

Anonymous

  • 79 Answers
  • Posted on Sep 15, 2010

SOURCE: Sir, i have a life fitness

please check the fuse of 0.3 amp is located in the front of the machine revises this swicth home underneath the left side of the machine or check for side always in the left if the cables are not disconnected last step and check the capacitor is located on the hoist motor any question send me a message [email protected]

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

My Reebok Jet 200 is stuck at an incline
If your Reebok Jet 200 treadmill is stuck at an incline and you are unable to lower the incline to the 0 position, there are a few things you can try to fix the problem:
  1. Check the incline motor and make sure that it is properly installed and functioning. If the motor is damaged or not functioning properly, it may be causing the incline to remain stuck.
  2. Check the incline control board and make sure that it is properly connected to the incline motor and other treadmill components. If the control board is damaged or not functioning properly, it may be causing the incline to remain stuck.
  3. Check the incline cable and make sure that it is not frayed or damaged. If the cable is damaged, it may be causing the incline to remain stuck.
  4. Check the treadmill's belt and make sure that it is properly aligned and tightened. If the belt is misaligned or loose, it may be causing the incline to remain stuck.
  5. Check the treadmill's power supply and make sure that it is properly connected and functioning. If the power supply is not functioning properly, it may be causing the incline to remain stuck.
If you have tried all of these steps and are still having issues with the incline on your Reebok Jet 200 treadmill remaining stuck, you may want to consult a professional for further assistance. A treadmill repair technician will be able to diagnose the problem and recommend the best course of action to fix it.
Read full answer
Dec 24, 2022 • Reebok Exercise & Fitness
1helpful
1answer

The lift will not incline now in normal mode, but in Maintenance mode manual it inclines and declines, code Incline Inoperative Continue if Desired. What steps should I follow. Thank you Ernesto
replace home switch sensor
Read full answer
Oct 08, 2013 • Life Fitness LifeFitness 9500HR Treadmill...
0helpful
1answer

We have Lifefitness 9500HR Treadmill. I am getting a Bad Controller Error. We have two 9500HR models. I swapped out Controller, with working 9500HR and still get Error. Keeps going into Notify Maintenance....
I would suggest swapping the consoles to see if the problem follows. If this does not help you figure it out, you are more than likely looking at a wiring issue.
Read full answer
Sep 23, 2013 • Life Fitness Exercise & Fitness
0helpful
2answers

I have 9500HR Treadmill Lifefitness, Lift keeps increasing when pushing the down button.
RUN the software calibration for easy diagnostic and fix it. Go under the HOOD motor, and follow the steps.
The Steps for Newer Style Console Calibration:
  1. Locate the calibration area on the rear or underside of the console (a hole, near the console's center, that goes through to the electronics board. (This hole should not have a screw in it.)
  2. Insert a pencil (eraser end), into the hole and feel around for the cal button (will click when pressed).
  3. Press the button 2 times (with the pencil eraser). The first click should show CL11 in the console, the second click should show CL21.
  4. If the process was done correctly, and CL21 appears in the console, you are in "calibration mode." The next few steps consists of pressing buttons on the console and observing settings. This will not require any other tools.
  5. Press ENTER. CL22 should display in the TIME window and (??) in the SPEED window.
  6. Press ENTER. CL23 should display in the TIME window and (??) in the SPEED window.
  7. Press ENTER. CL24 should display in the TIME window and (??) in the SPEED window.
  8. Press ENTER. CL25 should display in the TIME window and (??) in the SPEED window.
  9. Press ENTER. CL26 should display in the TIME window. You should then see the letter "E."
  10. Press ENTER. You should see "SS" or "55" in the console.
  11. Push the STOP/START button. For safety, at this point, you should step off, or be off, the treadmill.
  12. Push the ENTER button. The walking belt should start to move, accelerate to maximum speed, then stop on its own.
  13. When the belt stops, the incline should self test by raising to its highest incline position, then lowering back down to its lowest position.
  14. Once the incline test is complete, push the POWER button 2 times. The unit should shut off and the console should go completely blank. If this happens, the treadmill is done calibrating and is ready for use.
If the letter "F" appears in the SPEED or INCLINE window when the power button is pressed 2 times, the treadmill is indicating a failure somewhere either in the SPEED or INCLINE (depending on the window the "F" appeared in). Troubleshooting the failure would be the next step.
God bless you
Read full answer
Sep 23, 2013 • Life Fitness LifeFitness 9500HR Treadmill...
0helpful
2answers

I had a lift motor go out on my 9500hr treadmill, I changed the lift motor. Now when i try to get the treadmill to inclin it only does it in the manual mode. when i try to get it to incline through the...
1) Try to measure the if there are 110Vca in the terminal in forward or reverse.
2) Try to measure the ESR from Capacitor and replace it.
3) If you system as LIMIT Switch , test for continuity with DMM for faulty and replace, or some wires loose or disconnect.
4) If you system are Relais see if the relais for UP and down, and working most of them has LED that will be LIT indicating working or NOT
5) If NOT voltage Vca are NOT, coming from The Controller Board Motor, REPLACE IT,
Control board motor has 3 power supply: 1) Console board 2)Elevation Motor 3) Main Motor.
Some IGTBs are Defective.
Blessing.
[email protected]
cell+whatsAPP:+50588611441

LED Blink Patterns on the Control Board Treadmill
Read full answer
Nov 25, 2017 • Life Fitness 9500HR Next Generation...
0helpful
1answer

I have the TR 9500 HR - Next Generation. When a program runs, the button does not respond Incline - Incline setting. If the machine is at rest tilt can be performed in service menu / System Test / LIFT...
This isn’t something you need a professional to do for you.
Read full answer
Jan 24, 2018 • Life Fitness 9500HR Next Generation...
0helpful
1answer

Sir, i have a life fitness 9500hr. I hit start screen reads incline inoperable. Everything else works but won't incline. Thanks
please check the fuse of 0.3 amp is located in the front of the machine revises this swicth home underneath the left side of the machine or check for side always in the left if the cables are not disconnected last step and check the capacitor is located on the hoist motor any question send me a message [email protected]
Read full answer
Aug 15, 2010 • Life Fitness 9500HR Next Generation...
0helpful
1answer

Unit will not start. it does work in maintenance mode. All fuctions work in the maintenance mold. When using the quick start or other setting to start workout, the unit does not start. " Please Wait " is...
Get back into System test hit enter it will automatically to a check once completed. Then go to Lift motor module Go to manual incline and go to maximum incline then to 0 incline then get out of system test unplug unit for about 30 seconds. Then plug unit in if this does not work the limit or home switch may be the culprit
Read full answer
Jun 29, 2010 • Life Fitness 9500HR Next Generation...
0helpful
1answer

Hi have life fitness 9500hr.when i opne MOTER
Every time I have gotten this message, I have had to replace the motor controller.
Read full answer
Feb 27, 2010 • Life Fitness 9500HR Next Generation...
0helpful
1answer

Hi! i have a life fitness 9500HR treadmill and it says incline error on the screen! and the incline doesn't work?? can i fix it somehow?
Unplug the treadmill . Remove front cover. On the right hand side if you are facing the front - in the siderail is a white switch that tells the treadmill it is all the way down. Check that it is in place and clean.
If you plug the treadmill in.{Do not touch any thing in the motor compartment} When you press start it should go all the way down [home] to contact the switch. You can also see the lit motor turn at this time before the belt will move it must be all the way down.
Read full answer
Feb 07, 2010 • Life Fitness 9500HR Next Generation...
Not finding what you are looking for?

View Most Popular

9500HR Next Generation Remanufactured Treadmill

  • Exercise & Fitness

Related Question

My Reebok Jet 200 is stuck at an incline

  • Reebok Exercise & Fitness

337 views

Ask a Question

Usually answered in minutes!

Popular Questions

Speed Stall error

Life Fitness F1 Smart Treadmill

Treadmill wont run its saying waxer empty and

Life Fitness 95Ti Remanufactured...

I WANT TO CHANGE KILOMETER TO MILe

Life Fitness 95Ti Treadmill 95 Ti

Where is battery located for LifeFitness'

Life Fitness Exercise & Fitness

How do you change the

Life Fitness Exercise & Fitness

Best Treadmill
Best Treadmill

View all Fixya Reports

Top Life Fitness Exercise & Fitness Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Grand Canyon Tech
Grand Canyon Tech

Level 3 Expert

3867 Answers

Mike Cairns
Mike Cairns

Level 3 Expert

3054 Answers

Are you a Life Fitness Exercise and Fitnes Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...