Cannot get scanner programed

there's a program called 123scan2 where you can configure a prefix and outputs a program barcode

I no longer provide support for any scanners. As a Police Dispatcher I was working when two police officers were ambushed and killed because a person listening to a scanner told the suspects the police were coming. They should be outlawed.

Hi,

There is no need of installing driver for fi-5530c2 scanner as the driver comes bendled in the fi-5750c scanner. Hence, please install the driver for fi-5750c.On the application, you need to chnage the scanner model under "Select Scanner" menu.

Hope the above information is helpful.

Thanks & regards,
ScanCare

With the scanner powered ON,

1. Press [HOLD].
“HOLD” appears on the
display.
2. Press [PROG]. CH appears
and blinks to indicate that you
are in the Programming Mode.
To change the displayed frequency,
use [UP] or [DOWN]
while “CH” is blinking.
3. Press [PRIVATE]. “PRIVATE”
appears on the display.
If you want to program it into
another bank, press the
desired bank key. The lowest
open channel appears on the
display.
2 screens alternate to indicate
that open channel is available
to be programmed.
The scanner automatically
selects the lowest open
channel (000.0000) for easy
programming. If all channels
have been programmed (there
are no open channels in the
bank), channel 1 appears.
Use [UP] or [DOWN] to select
a new channel and even overwrite
old channels.
4. Press [PROG] to store the
frequency in the desired
channel.
Note: Press [BAND] to escape
from programming mode before
step 4.

Need the manual? You can download/print it here:

http://www.uniden.com/pdf/BC350Com.pdf

For a comprehensive database of active frequencies in your area, visit:

www.RadioReference.com

You'll need to program the radio frequencies into your scanner before it will scan . For a list of frequencies in Anoka County CLICK HERE .
For specific programing instructions for your UNIDEN refer to your owner's manual. They will give you a step by step instruction on how to program the frequencies into your scanner memory (If you need a manual, CLICK HERE
...be sure to select the scanner option on their pull-down menu.
THEN when you have the radio frequencies stored into your scanner, you'll be able to press scan and away you go.
Be sure to adjust the squelch just high enough to eliminate the static...turn the squelch counterclockwise until you hear loud static, then turn Clockwise just enough to silence static...
Let us know if you still have trouble.

You will also need a software package to program your scanner. Unfortunately the cable does not come with the software. Try going to www.starrsoft.com and download a program called Win97. It is free for 30 days and makes programming a breeze and it can also interface with radioreference.com (if you are a paying subscriber to the radioreference.com site) to download automatically.If you don't mind doing a little typing, you can view the info on the site for free and enter it into the program.

http://support.radioshack.com/manuals/ome20-525.pdf

Here are all the scanner manuals. unfortunately yours is not there. I would check the model # again with the ones on the list. Or look at one the is close to yours to figure it out. sorry I can not help anymore

http://www.uniden.com/index/manuals_results.cfm?cat=3

Good Luck.

Here are the talk groups from Radireference.com. this is the best reference I have found on the web. The talkgroups are for the Clark Regional Emergency Services Agency (CRESA) System. Here is a link to that page in Radio Reference

http://www.radioreference.com/apps/db/?sid=106

41680 - Police Car-to-Car
41712 - Common

I hope this helps - elijam1

Here is another site for any of your other scanner needs. they sell scanners, antenns, and even programming.

http://www.scannermaster.com/?Click=37131

I searched pretty hard and couldn't find any Vista drivers. I assume that scanner is relatively old. You can try this, but I don't know if your scanner has software:

Go to Start, then Control Panel, Programs, and under Program Features you'll see something that says "Use an older program with this version of Windows." Try messing with that and see if you can figure anything out. But I'm pretty sure there are no Vista drivers for that scanner.