Don't know which buttons on my bow flex strapless heart monitor to push to set the time

To reset your Timex 637 T5G951 WR 30 heart monitor, you can follow these steps:

1. Press and hold the "Mode" button on the front of the watch for three seconds until the watch display shows "Settings."
2. Press the "Next" button on the side of the watch to scroll through the settings menu until you reach "Reset."
3. Press the "Mode" button to select "Reset." The display will show "Yes" and "No."
4. Use the "Next" button to scroll to "Yes," and then press the "Mode" button to confirm.
5. The watch will reset and return to the time display.

Note: Resetting your Timex 637 T5G951 WR 30 heart monitor will erase all your saved data and settings, so you will need to set it up again after the reset. If you need to keep your data, consider transferring it to another device before resetting the watch.

click on this link find your watch click on it then you can download the instruction manual
http://www.sportline.com/products/heart-rate-monitors.htmlhttp://www.sportline.com/products/heart-rate-monitors.html

Unfortunately MIO do not have repair services in Australia, probably would have to send it back to the US. Hopefully you can work with the seller to fix the issue. I know when you buy through mioglobal.com their customer service is excellent.

Go into settings.

Press the center button on the right hand side of the watch 1 time you will see settings watch time & date appear in the display.

Press the bottom button on the right side of the watch1 time to get into the TRAINING SETTINGS FUNCTION.

When you see TRAINING SETTINGS in the display press the center button on the right side of the watch once.

You are in TRAINING SETTING mode.

Press the bottm button on the right hand side of the watch 3 times until you see
ZONE LIMITS displayed.

When you see ZONE LIMITS displayed press the center button on the right side of the watch 1 time to enter into the ZONE LIMITS FUNCTION.

Now, you should see the lower end heart rate limit number blinking.

To adjust this number use the top button on the right hand side of the watch to increase this limit or lower button on the right hand side to decrese it.

When you have it set where you want it press the center button 1 time to save that setting.

Now you should see the upper limit number blinking.

Follow the same steps to set the upper heart rate limit.

When you have pressed the ceter button to set the upper limit you have completed setting the heart rates limits and the display should read: LIMITS SET!

Press and hold the reset button, for 5 seconds, while in Time mode. the heart monitor will reset and the symbol reappear on the screen

On my tips and tricks page is a link to the user manual.

The trick with the FS1 is that you have to wait between button pushes. Don't try to skip ahead of the pace of the watch, it is slow to set anything. That is the rub with 1 button operations.

Push the button, wait for the prompt, enter the info, push the button, wait for the prompt, etc.

if after trying this it still doesn't work you will either need to take it back and exchange or send into polar. There is a warranty service available. Again that link is under my tips and tricks.

Have you contacted their customer service team? They are great at resolving issues and really stand behind their product. Their Facebook page MIOWatch also has lots of troubleshooting and FAQs too.

Thank you for contacting FixYa.<br /> Motiva is owned by Philips. You can download at the following link:<br /> <a href="http://www.healthcare.philips.com/us_en/products/telehealth/Products/motiva.wpd">http://www.healthcare.philips.com/us_en/products/telehealth/Products/motiva.wpd</a><br /> Best regards.

Have tried going to a watch shop ? It may sound a bit obvious, but looking at your watch and comparing it with mine, I think that a standard strap might fit.

You have nothing to loose by asking and it tends to be expensive to send them back to the makers.

This is really easy to do yourself. Get a CR1632 battery, unscrew the four screws on the back (dont tip the watch as there is a small spring in the watch), unclip the metal band holding in the old battery noting the way 'round the battery is in (minus side up), pop in new battery and push clip back down, when re-fitting the back make sure the spring mentioned earlier lines up with the white sticker with a hole in it on the inside of the watch back, screw down the back. After you have re done all your settings you may need to re-aquaint the watch with the strap, to do this put on the watch and strap, set the heart monitoring going, bring the watch up close to the 'Polar' logo on the chest strap until the time is displayed, should now be all set up.

Andy