KitchenAid KSBP25FKSS Side by Side Refrigerator Logo
A
Anonymous Posted on Mar 17, 2014

Frigidaire refrigerator filter status light is red

1 Answer

John Tripp

Level 3:

An expert who has achieved level 3 by getting 1000 points

Superstar:

An expert that got 20 achievements.

All-Star:

An expert that got 10 achievements.

MVP:

An expert that got 5 achievements.

  • KitchenAid Master 4,656 Answers
  • Posted on Mar 18, 2014
John Tripp
KitchenAid Master
Level 3:

An expert who has achieved level 3 by getting 1000 points

Superstar:

An expert that got 20 achievements.

All-Star:

An expert that got 10 achievements.

MVP:

An expert that got 5 achievements.

Joined: Oct 20, 2007
Answers
4656
Questions
2
Helped
1679144
Points
14883

That information is in the user manual that covers your model number. Below is the procedure for a Side by Side. To look for your manual click=> HERE
Press and hold the Water Filter button
on the Ice & Water Dispenser control
panel for three seconds. When the display
changes from "Red" to "Green," the status
has been reset.

I am here should you need me, Thanks John Tripp Appliance 911
Contact Me Here

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

How to reset the order filter feature

Good Afternoon Friend,

I understand that the order filter light is showing on your Frigidaire refrigerator, model# DGHF2360PF, and you want to know how to reset it. What you will need to do is press and hold the Water Filter button on the Ice & Water Dispenser control panel for three seconds. When the display changes from Red to Green, the status has been reset. I hope this is helpful.

-Best regards-
WP
0helpful
1answer

Frigidaire filter status light will not reset

Check to be sure your water source is on. Low pressure may make the filter sensor think there is a plugged filter.
0helpful
2answers

I have the frigidaire refrigerator & I replaced the water filter ,how can I rest the water fliter into green light?

Press and hold the filter reset button on the front of despensor 10-15 seconds until the green red and orange lights come on.
0helpful
1answer

Filter stuck in a Frigidaire FRS26R4A Side by Side Refrigerator. Tried and tried but pushing the release button does nothing. I've tried using a hefty screwdriver to pry it out while pushing the release...

Removing and replacing a water filter - upper right hand corner inside location

Filters situated up front in the refrigerator compartment of Frigidaire-built side-by-side refrigerators are relatively simple to replace. Follow these steps:
  1. Open the door of the refrigerator compartment of your Frigidaire brand side-by-side refrigerator. The filter is located in the upper right hand corner. It has a push button for quick release just to the right of the filter.


  2. Locate the icemaker On/Off power switch and place it in the OFF (o) position.


  3. Push in on the filter release button and pull the filter all the way out to remove it. Remove new filter from its packaging and remove the protective plastic caps. Insert the new filter in the same manner it was removed. Make sure to push in firmly on the filter until you hear the filter cartridge click in place.


  4. Return the icemaker's power switch to the On (l) position.


  5. Condition the filter by running water through the dispenser for about three minutes. This will flush the filter of all fine carbon particles.


  6. In some models, you will have to reset the filter status light. It is located on the ice and water dispenser control panel. Push in on it for ten to fifteen seconds until the green, red, and amber lights flash. If your refrigerator model does not have a filter status light, you should make a note on a calendar, or place a month sticker on your filter to remind you to replace the filter again in six month's time.



Note: Replacing this type of filter is a quick process - there is no need to unplug your refrigerator or shut off the water supply when replacing it. Also, this filter should be replaced every six months.
1helpful
1answer

Side by side refrig - ice maker and water don't work after replacing the filters. is there a re-set?

Removing a water filter from the inside of your Frigidaire brand refrigerator:


Removing and replacing a water filter - upper right hand corner inside location

Filters situated up front in the refrigerator compartment of Frigidaire-built side-by-side refrigerators are relatively simple to replace. Follow these steps:
  1. Open the door of the refrigerator compartment of your Frigidaire brand side-by-side refrigerator. The filter is located in the upper right hand corner. It has a push button for quick release just to the right of the filter.


  2. Locate the icemaker On/Off power switch and place it in the OFF (o) position.


  3. Push in on the filter release button and pull the filter all the way out to remove it. Remove new filter from its packaging and remove the protective plastic caps. Insert the new filter in the same manner it was removed. Make sure to push in firmly on the filter until you hear the filter cartridge click in place.


  4. Return the icemaker's power switch to the On (l) position.


  5. Condition the filter by running water through the dispenser for about three minutes. This will flush the filter of all fine carbon particles.


  6. In some models, you will have to reset the filter status light. It is located on the ice and water dispenser control panel. Push in on it for ten to fifteen seconds until the green, red, and amber lights flash. If your refrigerator model does not have a filter status light, you should make a note on a calendar, or place a month sticker on your filter to remind you to replace the filter again in six month's time.



Note: Replacing this type of filter is a quick process - there is no need to unplug your refrigerator or shut off the water supply when replacing it. Also, this filter should be replaced every six months.



4helpful
1answer

Red light stays on after changing the water filter and running about 2 gallons through it

Water Filter Status Indicator
Light (select models)
The Water Filter Status Indicator Light serves as a
reminder to replace the water filter. A green light
indicates that the filter is in good condition. A red light
indicates the filter should be changed. Once light turns
red, it will remain red until function is reset.
To Reset Indicator:
• Press and hold both the Lock and Water
buttons simultaneously for four seconds. The
green filter status indicator light will flash
three times when the function has
successfully reset.
0helpful
1answer

Change filter light

Water Filter Status Indicator
Light (select models)
The Water Filter Status Indicator Light serves as a
reminder to replace the water filter. A green light
indicates that the filter is in good condition. A red light
indicates the filter should be changed. Once light turns
red, it will remain red until function is reset.
To Reset Indicator:
• Press and hold both the Lock and Water
buttons simultaneously for four seconds. The
green filter status indicator light will flash
three times when the function has
successfully reset.
Sea Breeze
2helpful
1answer

I have a Frigidaire Model FRS26ZSH need water filter instruction

Filter Status Press and Hold five seconds to reset light. (This light will tell you when to replace the water filter.)
press the button to the right of water filter to release filter...
0helpful
1answer

Changing light after installing new water filter

Water Filter Status Indicator Light
(select models)
The Water Filter Status Indicator Light serves as a
reminder to replace the water filter. A green light
indicates that the filter is in good condition. A red light
indicates the filter should be changed. Once light turns
red, it will remain red until function is reset.
To Reset Indicator:
• Press and hold both the LOCK and WATER
buttons simultaneously for four seconds. The
green filter status indicator light will flash
three times when the function has
successfully reset.
0helpful
1answer

Frigidaire filter problem..

After changing the filter it is necessary to reset the filter status light. Press the filter status reset button for 3 to 15 seconds until the green light flashes.

If you want to look at the entire service manual you can access it at : http://www.fixya.com/support/p61551-frigidaire_frs26r4a_side_by_side/manual-4115/page-14
Not finding what you are looking for?

1,088 views

Ask a Question

Usually answered in minutes!

Top KitchenAid Refrigerators Experts

vince

Level 3 Expert

2530 Answers

Cindy Wells

Level 3 Expert

6688 Answers

Brad Brown

Level 3 Expert

19187 Answers

Are you a KitchenAid Refrigerator Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...